Packard Bell M5801 manual Assembly motherboard

Page 49

4.8Press down the memory

4.9Memory install rule

		DIMM4	DIMM2	DIMM3	DIMM1
	1x1G		1GB
	2x1G		1GB		1GB
	3x1G	1GB	1GB		1GB
	4x1G	1GB	1GB	1GB	1GB
	1x2G		2GB
	2x2G		2GB		2GB
	1x1G		2GB		1GB
	+1x2G		2GB		1GB
	+1x2G

5.Assembly motherboard

5.1 Pushing rear I/O Shield in chassis

43

Image 49

Contents Ixtreme M5801 Service Guide Revision History Date Chapter UpdatedCopyright Conventions Preface 103 Introduction Introducing the MotherboardFeatures Dimensions and weight Bios FirmwareExpansion Options Integrated I/OLabel Component Mainboard ComponentsCintrusion Block Diagram Icon Component Description Ixtreme M5801USB ports Connects to USB 2.0 devices USB mouse, USB camera Rear view Color/Use Headphone Audio Jack Function Table1CH Component Description Port IntroductionMouse PS/2 or USB, manufacturing option System PeripheralsKeyboard PS/2 or USB, manufacturing option SpeakersCard Reader Option Bios Hotkey List Hardware Specifications and ConfigurationsSpecification Main Board Major ChipsCache Memory System MemoryVideo Interface Audio InterfaceIDE Interface Power ManagementUSB Port Devices Idle Shut DownDevice Standby Mode Power Management Function Acpi support functionGlobal Standby Mode Suspend ModeAbout the Setup Utility Using BiosStandard Configuration Entering the Setup UtilitySetup Utility Menus Updating the Bios Item Help Product InformationDate and Time Standard Cmos FeaturesA.R.T. Auto UAHCI Port1 /Port2 /Port3 /Port4 /Port5 /Port6Halt On All, But Keyboard Quick Boot Enabled Advanced Bios FeaturesQuiet Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter USB Beep Message Disabled Boot Up NumLock OnAdvanced Chipset Features Integrated Peripherals Deep Power Off Mode Enabled Power Management SetupPower On by RTC Alarm Disabled Power On by PCIE/PCI Devices DisabledWake Up by USB KB/Mouse Enabled Wake Up by PS/2 KB/Mouse EnabledRestore On AC Power Loss Last State PC Health Status Smart Fan EnabledSpread Spectrum Enabled Enable Clock to All DIMM/PCI EnabledFrequency/Voltage Control Supervisor Password Not Installed Bios Security FeaturesUser Password Not Installed Change Supervisor Password Press EnterSave & Exit Setup Load Default SettingsMachine Disassembly and Replacement Before You Begin General InformationOpening the chassis Standard Assembly ProcessRemoving front bezel and HDD Cage Page Setting the Motherboard Install the PSUPage Page Assembly motherboard Page Insert the ODD/HDD ODD Installed on SATA4 HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Insert Add-on card Close the Front BezelPage Page Install system fan Overview Opening the computer Standard Disassembly ProcessRemoving the Front Bezel Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the Main Board Removing the System FanPage Page Removing the power-supply Removing the HDD in HDD Carrier Page Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Bios Messages Action/FRU Post Error Messages ListSpecifics about the type and location of the memory error Error Symptom Action/FRU Processor / Processor Fan Error Symptoms ListMain board and Memory Hard Disk DriveAudio Error Symptom Action/FRU CD/DVD-ROM DrivePower Supply Error Symptom Action/FRU Video and MonitorParallel/Serial Ports KeyboardOther Problems Error Symptom Action/FRUUndetermined Problems Safety Precautions Jumper and Connector InformationInstalling the Motherboard in a Case Choosing a Computer CaseSetting Jumpers Checking Jumper SettingsJumper Settings Checking Jumper SettingsJumper Type Description Setting Default IIIustration Connecting 24-pin power cable Connecting Case ComponentsPwrfan Cooling Fan Power Connector Pin Signal Name Function Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPin Signal Name ATX12V ATX 12V Power Connector Pin Signal NamePower/Sleep/Message waiting LED Pin Signal Name FunctionReset Switch Power SwitchInstalling the Processor Installing HardwareBefore installing the Processor Following illustration shows CPU installation components CPU Installation ProcedureInstallation Procedure Installing Memory ModulesMemory Memory Bus Sata cable optional Sata power cable optional Installing Serial ATA Hard DrivesPCIE16X Slot Installing Add-on CardsOnboard PCI interface does not support 64-bit Scsi cards FAUDIO1 Front Panel Audio header Connecting Optional DevicesSPDIFOUT1 Spdif out headerOption Sata 1~6 Serial ATA connectorsSPIDEBUG1 ChassisPB 30L w/ HDD carrier ME BOM FRU Field Replaceable Unit List Exploded DiagramRAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM 101 102 FRU List