Packard Bell M5801 manual UHard Disk Drive Priority Press Enter

Page 31

uHard Disk Drive Priority (Press Enter)

Scroll to this item and press <Enter> to view the following screen:

CMOS Setup Utility - Copyright (C) 1985-2010, American Megatrends, Inc.

Hard Disk Drive Priority

		Item Help
Hard Disk Drive Priority
Hard Disk Drive Priority		Specifies the boot
-------------------------------------------------------------------		Specifies the boot
1st Drive	ST3320418AS	sequence from the
		available devices.












		↑↓→←：Move	Enter：Select +/-/：Value	F10：Save & Exit Setup
		F1：General Help	F9：Load Default Settings	Esc： Exit Without Saving

Press <Esc> to return to the Advanced BIOS Features screen.

uOptical Disk Drive Priority D/DVD Drives (Press Enter)

Scroll to this item and press <Enter> to view the following screen:

CMOS Setup Utility - Copyright (C) 1985-2010, American Megatrends, Inc.

Optical Disk Drive Priority

Item Help

Optical Disk Drive Priority

------------------------------------------------------------------ Specifies the boot

1st Drive	ATAPI DVD A DH16A6S	sequence from the
		available devices.











		↑↓→←：Move	Enter：Select +/-/：Value	F10：Save & Exit Setup
		F1：General Help	F9：Load Default Settings	Esc： Exit Without Saving

Press <Esc> to return to the Advanced BIOS Features screen.

25

Image 31

Contents Ixtreme M5801 Service Guide Revision History Date Chapter UpdatedCopyright Conventions Preface 103 Introduction Introducing the MotherboardFeatures Integrated I/O Bios FirmwareDimensions and weight Expansion OptionsLabel Component Mainboard ComponentsCintrusion Block Diagram Icon Component Description Ixtreme M5801USB ports Connects to USB 2.0 devices USB mouse, USB camera Rear view Color/Use Headphone Audio Jack Function Table1CH Component Description Port IntroductionSpeakers System PeripheralsMouse PS/2 or USB, manufacturing option Keyboard PS/2 or USB, manufacturing optionCard Reader Option Main Board Major Chips Hardware Specifications and ConfigurationsBios Hotkey List SpecificationAudio Interface System MemoryCache Memory Video InterfaceDevices Idle Shut Down Power ManagementIDE Interface USB PortSuspend Mode Power Management Function Acpi support functionDevice Standby Mode Global Standby ModeEntering the Setup Utility Using BiosAbout the Setup Utility Standard ConfigurationSetup Utility Menus Updating the Bios Item Help Product Information Date and Time Standard Cmos FeaturesA.R.T. Auto UAHCI Port1 /Port2 /Port3 /Port4 /Port5 /Port6Halt On All, But Keyboard Quick Boot Enabled Advanced Bios FeaturesQuiet Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter USB Beep Message Disabled Boot Up NumLock OnAdvanced Chipset Features Integrated Peripherals Power On by PCIE/PCI Devices Disabled Power Management SetupDeep Power Off Mode Enabled Power On by RTC Alarm DisabledWake Up by USB KB/Mouse Enabled Wake Up by PS/2 KB/Mouse EnabledRestore On AC Power Loss Last State PC Health Status Smart Fan EnabledSpread Spectrum Enabled Enable Clock to All DIMM/PCI EnabledFrequency/Voltage Control Change Supervisor Password Press Enter Bios Security FeaturesSupervisor Password Not Installed User Password Not InstalledSave & Exit Setup Load Default SettingsMachine Disassembly and Replacement Before You Begin General InformationOpening the chassis Standard Assembly ProcessRemoving front bezel and HDD Cage Page Setting the Motherboard Install the PSUPage Page Assembly motherboard Page Insert the ODD/HDD ODD Installed on SATA4 HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Insert Add-on card Close the Front BezelPage Page Install system fan Overview Opening the computer Standard Disassembly ProcessRemoving the Front Bezel Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the Main Board Removing the System FanPage Page Removing the power-supply Removing the HDD in HDD Carrier Page Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Bios Messages Action/FRU Post Error Messages ListSpecifics about the type and location of the memory error Hard Disk Drive Error Symptoms ListError Symptom Action/FRU Processor / Processor Fan Main board and MemoryAudio Error Symptom Action/FRU CD/DVD-ROM DriveKeyboard Error Symptom Action/FRU Video and MonitorPower Supply Parallel/Serial PortsOther Problems Error Symptom Action/FRUUndetermined Problems Choosing a Computer Case Jumper and Connector InformationSafety Precautions Installing the Motherboard in a CaseSetting Jumpers Checking Jumper SettingsJumper Settings Checking Jumper SettingsJumper Type Description Setting Default IIIustration Connecting 24-pin power cable Connecting Case ComponentsATX12V ATX 12V Power Connector Pin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPwrfan Cooling Fan Power Connector Pin Signal Name Function Pin Signal NamePower Switch Pin Signal Name FunctionPower/Sleep/Message waiting LED Reset SwitchInstalling the Processor Installing HardwareBefore installing the Processor Following illustration shows CPU installation components CPU Installation ProcedureInstallation Procedure Installing Memory ModulesMemory Memory Bus Sata cable optional Sata power cable optional Installing Serial ATA Hard DrivesPCIE16X Slot Installing Add-on CardsOnboard PCI interface does not support 64-bit Scsi cards FAUDIO1 Front Panel Audio header Connecting Optional DevicesSPDIFOUT1 Spdif out headerOption Sata 1~6 Serial ATA connectorsSPIDEBUG1 ChassisPB 30L w/ HDD carrier ME BOM FRU Field Replaceable Unit List Exploded DiagramRAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM 101 102 FRU List