FieldServer FS-8704-12 instruction manual Appendix B. Error Messages, Message Action

Page 22

FS-8704-12_GE-EGD Manual

Page 22 of 26

Appendix B. Error Messages

Multiple protocol drivers may exist on a FieldServer. Each driver may produce its own error messages and the FieldServer itself may produce error messages.

Message

Action

EGD:#1 Error. Can’t init UDP.

This is a fatal error. The FieldServer needs to be re-initialized

EGD:#2 Error. Can’t get a

or you need technical support from FieldServer Technologies.

socket.

 

EGD:#3 Error. Protocol does

The rdbc/rdb/rdbx functions are not supported by this protocol.

not support active polling.

The device you wish to poll must be configured to 'produce' its

Change function for

data and this driver will 'consume' the data using passive Map

mapDesc=<%s>

Descriptors.1

EGD:#4 Error. Producer ID

Each Map Descriptor requires a producerID.1

required for mapDesc=<%s>

 

EGD:#5 Error. Exchange ID

Each Map Descriptor requires an exchangeID.1

required for mapDesc=<%s>

 

EGD:#6 FYI. No data type

 

specified. Defaulted to <Byte>

This is a warning only. You can eliminate the warning by

EGD:#7 FYI. Data type not

editing the CSV file.1

recognized. Defaulted to

 

<Byte> for mapDesc=<%s>

 

EGD:#8 Error. Don't know GE

An illegal data type has been used.1

Data Type(%d) for

mapDesc=<%s>

 

EGD:#9 Error. Incoming data

An EGD producer has sent a data packet to the FieldServer

but the driver cannot find a passive Map Descriptor to use to

from ip=<%s>

process and store the incoming data. It’s possible that the

producerID=<%s>

producer has been incorrectly configured and that the packet

exchangeID=(%d) is being

was not intended for the FieldServer. Alternatively, make a

abandoned.

new Map Descriptor which will handle this data.

 

EGD:#10 Error. Don't know GE

An illegal data type has been used.1

Data Type (%d) for

mapDesc=<%s>

 

EGD:#11 FYI. You could have

This message requires no action, but refer to Appendix B.1 of

used a mapDesc called <egd-

this manual to see whether you will benefit from exposing

ii> to expose diagnostic info.

some driver internal diagnostic data.

EGD:#12 Invalid IP. Too many

IP address is more than 15 characters in length.1

characters.

 

EGD:#13 Invalid IP <%s>

Insufficient points in the IP address. 1

EGD:#14 Error. The mapDesc

Increase the data length parameter for this Map Descriptor

called <egd-stats> is too short

Make sure the Data Array is long enough too.

EGD:#15 FYI. You could have

 

used a mapDesc called <egd-

Refer to Appendix B.10 \r \h Appendix B.1} for more

stats> to expose diagnostic

information.

info.

 

1Edit the CSV file, download to the FieldServer and restart the FieldServer for the changes to take effect.

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com

Image 22
Contents FS-8704-12 GE-EGD Ethernet Global Data Table of Contents GE-EGD Ethernet Global Data Description FS-8704-12GE-EGD ManualProvided by the Supplier of 3rd Party Equipment FieldServer Technologies DescriptionHardware Connections Section Title Configuring the FieldServer as a GE-EGD ClientData Arrays Column Title Function Legal ValuesClient Side Node Descriptors Client Side Connection DescriptorsFS-8704-12GE-EGD Manual Example Driver Specific Map Descriptor Parameters FS-8704-12GE-EGD Manual Column Title Function Legal Values Map Descriptor Example Map Descriptor Basics Map Descriptor Example a Simple Consumer Map DescriptorMap Descriptor Example Multiple Consumer Map Descriptor Server Side Node Descriptors Wrbc Timing Parameters IeeeMap Descriptor Example FS-8704-12GE-EGD ManualPage 16 FS-8704-12GE-EGD Manual Create a CSV file that will consume the produced data Byte Dataq Appendix A.2. Data Types Appendix B. Error Messages Message ActionArray Contents Element Appendix B.1. EGD-ii EGD Internal IndicationsArray Element Contents Appendix B.2. Driver StatsAppendix C.2. Produced Time Stamp Appendix C.3. Status ValuesThis page Intentionally Left Blank