Eicon Networks 2440 manual Adjusting LAN Settings, If your LAN has a Dhcp Server

Page 26

However, if your computer is set to acquire its IP address dynamically from a DHCP server, you need only restart your computer (or reset the IP address manually using ‘winipcfg’ with Windows 9x or ‘ipconfig /renew’ for Windows 2000/NT). The Diva 2440 will assign the new address.

Adjusting LAN Settings

The following are further changes you may need to make to your LAN setup. However, due to the wide range of networking equipment and topologies, these are only guidelines.

If your LAN has a DHCP Server

If your LAN has a DHCP server, configure your DHCP server to return the address of the Diva 2440 as the ‘Default Gateway’ and ‘DNS Server’ to all clients.

If your LAN uses Static IP Addresses

If your LAN uses static addressing, you must configure the TCP/IP settings on each computer. Specifically, set each computer’s ‘Default Gateway’ and ‘DNS Server’ settings to the address of the Diva 2440.

If your LAN has a router

If you have a router on your LAN, it is likely configured as the default gateway for your computers. In this case, you will need to configure the routing table on your router to re-direct the appropriate traffic to the Diva 2440.

Setup

Page 26

Image 26

Contents Diva 2440 Adsl Router User’s Guide Second Edition June 206-378-02 Contents Index Introduction How Adsl WorksHardware Features General FeaturesAdsl and Network Features Introducing the Diva 2440 Adsl RouterPackage Contents Two Computers at Once Connection ScenariosOne Computer More than Two Computers Adsl line DivaMicrofilters How Adsl WorksSplitters and ‘Splitterless’ Operation Setup About Microfilters Technical SupportRequirements Connecting to Both PortsOverview Internet Account Information Ports and Indicator Lights PortsIndicator Lights Power LightEthernet Cable Notes Connect the CablesAdsl Cable Notes To continue Updating or reinstalling USB driversUSB Cable Notes Access the Diva 2440 Web Interface Complete the Internet Wizard LinkSetup Complete Optional Installing the Diva Assistant Setup Connecting a Second Computer LAN Setup About the Ethernet CableBuilt-in Dhcp Server General Setup ProcedureUsing the Diva Assistant to set on a LAN IP AddressingIf your LAN uses Static IP Addresses Adjusting LAN SettingsIf your LAN has a Dhcp Server If your LAN has a routerConfiguring TCP/IP TCP/IP SetupInstalling TCP/IP Windows 95/98Windows NT Apple Macintosh Mac OS 8 or later Verifying TCP/IP SettingsWindows Setup Troubleshooting Browser SettingsConnecting a Phone to the Pass-through Phone Port Connecting a Microfilter About MicrofiltersTechnical Support About the Diva Assistant General Information Resetting the DeviceUpgrading Firmware General Information Reset Settings to Factory Defaults Resetting the DeviceNormal Reset Boot ModeStarting the Web-based Configuration Interface Procedure‘Reset’ and other buttons on the Main Menu Editing Settings PagesBacking up the current configuration Configurations Saving, Restoring, and ResettingAccessing the Configuration Restoring a configuration from a fileUpgrading Firmware Backing up Configuration FilesOpening to the Firmware Maintenance Retrieving Firmware from the Eicon Networks Web SiteUsing your Diva Defining a password Login Password and other Security FeaturesLogin Password Erasing the system passwordNetwork Address Translation Automatic Log OutIP Filtering Security Level General Tab About the Diva AssistantLaunching the Diva Assistant Tools Tab Diagnostic Log TabPerformance Tab Advanced Topics Diva Requirements Setting up a VPN with Windows 95/98Virtual Private Networking InstructionsAdvanced Topics Setting up a VPN with Windows Connecting the VPN Security benefits Network Address TranslationHow It Works NAT static mappingsSpecifying a Default NAT Server Creating Static NAT Mappings‘Default NAT Server’ field Diva Prerequisites Command Line Interface CLIEstablishing a Telnet Connection Using the CLI Command Line ReferenceEnabling Tftp server support Using Tftp to Transfer FilesUploading/downloading configuration files Retrieving message.txt ExamplesLoading New firmware via Tftp Command Line Reference Cancel Notational ConventionsSET Adsl Modulation Type G9922 Multimode Adsl CommandsShow Adsl Configuration Show Adsl StatisticsSET ATM Service Category UBR CBR ATM CommandsShow ATM Configuration Show ATM VCDhcp Commands Ipaddress IP address of the Wins server Primary Wins serverSecondary Wins server Domain Domain name, a string of up to 31 charactersDelete Dhcp Staticmap ipaddress Ipaddress IP address of the entry to enable or disableIpaddress IP address of the entry to delete Show Dhcp StaticmapShow Ethernet Address Ethernet CommandsShow Ethernet Statistics Number Number of the filter that is to be deleted Filter CommandsNumber Position where new filter is to be added Number Number of the filter to editDiscard the data Filter applies to both incoming and outgoing data defaultNumber Number of the filter to copy Forward the data to the next filterApplies to UDP data Applied to TCP data defaultApplies to all data Applies to TCP connection SYN dataMacaddress Source or destination MAC address Enable Ethernet multicast filteringDisable Ethernet multicast filtering Type Hexidecimal number indicating type of Ethernet frameGeneral Commands Hours Range 00 to Minutes SecondsEnable Echo Server Disable Echo Server ResetReset Factory Enable Sysman Disable SysmanIP Commands General Show Statistics Ping ipaddress number sizeIP Routing Commands Show IP RouteTaskName Module name as seen in Show LOG. Examples Dhcp Logging and Internal Trace CommandsEnable all module messages UDP or TCP protocol NAT Network Address Translation CommandsEnable NAT Disable NAT Show IP NATPPP Commands Value Range 0-2147483647. DefaultEnable PPP Phase Logging Disable PPP Phase Logging Value Range 0-2147483647 milliseconds. DefaultEnable PPP Echo Request Disable PPP Echo Request Enable PPP FSM Logging Disable PPP FSM LoggingSET PPP Local Username SET PPP Local Password Show PPP ConfigurationShow Profiles Profile CommandsEnable Profile Disable Profile Connect DisconnectIndex Index of the VC taken from the SAR VC table SAR CommandsShow SAR Configuration Show SAR VC indexTftp Commands Enable Tftp Server Disable Tftp ServerShow Timeprotocol Configuration Time Protocol CommandsEnable Timeprotocol Disable Timeprotocol TimeServer Address of the time serverThis Section SpecificationsRegulatory Information for Canada Specifications General SpecificationsSoftware and Firmware Specifications FCC Part 68 Notice Regulatory Information for the United StatesDeclaration of Conformity Safety Notice Regulatory Information for Canada Regulatory Information for the European Union Safety Status TNV-3Power Consumption EU Declaration of ConformityIndex Index