Eicon Networks 2440 manual Windows NT

Page 28

5.Click the ‘DNS Configuration’ tab and select ‘Disable DNS.’ This instructs your computer to obtain DNS server information via DHCP.

6.Click ‘OK’, then click ‘OK’ again.

Note: You may be asked to insert your original Windows installation CD-ROM.

7.If prompted to restart your system:

•Click ‘No’ if you are next going to install the Diva Assistant. You are required to restart after installing this software, and clicking ‘No’ will save you some time.

•Click ‘Yes’ if you do not need to install the Diva Assistant. Your computer must be restarted in order to acquire a new IP address.

Windows NT 4.0

The following procedure describes how to install TCP/IP on Windows NT 4.0. If TCP/IP is already installed on your system, see Configuring TCP/IP (below). Note that if you have more than one adapter installed on your system, you will have to use the adapter that is in use by the Diva 2440.

1.Click ‘Start’, ‘Settings’, ‘Control Panel’.

2.Double-click the ‘Network’ icon. The Network dialog box appears.

3.Click the ‘Protocols’ tab.

•If ‘TCP/IP’ is not listed, go to Installing TCP/IP (below).

•If ‘TCP/IP’ is listed, then the protocol is already installed. Go to Configuring TCP/IP (below).

Installing TCP/IP

1.From the ‘Protocols’ tab, click ‘Add’.

2.Select ‘TCP/IP protocol’ as your network protocol, then click ‘OK’.

3.Click ‘Yes’ to use DHCP.

4.When prompted, insert the original Windows NT installation CD and enter d:\i386 (where d: is the drive letter of your CD drive), and click ‘Continue’.

5.Do not click the ‘OK’ button yet; next you will verify your TCP/IP settings. Go to Configuring TCP/IP (below).

Configuring TCP/IP

1.Click the ‘Protocols’ tab.

2.Select ‘TCP/IP protocol’, then click ‘Properties’.

3.Select ‘Obtain an IP address from a DHCP server’.

4.Click the ‘DNS’ tab. Delete any DNS addresses are configured.

5.Click ‘OK’.

Setup

Page 28

Image 28

Contents Diva 2440 Adsl Router User’s Guide Second Edition June 206-378-02 Contents Index Introduction How Adsl WorksGeneral Features Adsl and Network FeaturesHardware Features Introducing the Diva 2440 Adsl RouterPackage Contents One Computer Connection ScenariosTwo Computers at Once More than Two Computers Adsl line DivaSplitters and ‘Splitterless’ Operation How Adsl WorksMicrofilters Setup About Microfilters Technical SupportOverview Connecting to Both PortsRequirements Internet Account Information Ports and Indicator Lights PortsIndicator Lights Power LightAdsl Cable Notes Connect the CablesEthernet Cable Notes USB Cable Notes Updating or reinstalling USB driversTo continue Access the Diva 2440 Web Interface Complete the Internet Wizard LinkSetup Complete Optional Installing the Diva Assistant Setup Connecting a Second Computer LAN Setup About the Ethernet CableGeneral Setup Procedure Using the Diva Assistant to set on a LANBuilt-in Dhcp Server IP AddressingAdjusting LAN Settings If your LAN has a Dhcp ServerIf your LAN uses Static IP Addresses If your LAN has a routerTCP/IP Setup Installing TCP/IPConfiguring TCP/IP Windows 95/98Windows NT Windows Verifying TCP/IP SettingsApple Macintosh Mac OS 8 or later Setup Troubleshooting Browser SettingsConnecting a Phone to the Pass-through Phone Port Connecting a Microfilter About MicrofiltersTechnical Support Upgrading Firmware General Information Resetting the DeviceAbout the Diva Assistant General Information Resetting the Device Normal ResetReset Settings to Factory Defaults Boot ModeStarting the Web-based Configuration Interface Procedure‘Reset’ and other buttons on the Main Menu Editing Settings PagesConfigurations Saving, Restoring, and Resetting Accessing the ConfigurationBacking up the current configuration Restoring a configuration from a fileBacking up Configuration Files Opening to the Firmware MaintenanceUpgrading Firmware Retrieving Firmware from the Eicon Networks Web SiteUsing your Diva Login Password and other Security Features Login PasswordDefining a password Erasing the system passwordIP Filtering Security Level Automatic Log OutNetwork Address Translation Launching the Diva Assistant About the Diva AssistantGeneral Tab Performance Tab Diagnostic Log TabTools Tab Advanced Topics Setting up a VPN with Windows 95/98 Virtual Private NetworkingDiva Requirements InstructionsAdvanced Topics Setting up a VPN with Windows Connecting the VPN Network Address Translation How It WorksSecurity benefits NAT static mappingsSpecifying a Default NAT Server Creating Static NAT Mappings‘Default NAT Server’ field Diva Establishing a Telnet Connection Command Line Interface CLIPrerequisites Using the CLI Command Line ReferenceUploading/downloading configuration files Using Tftp to Transfer FilesEnabling Tftp server support Loading New firmware via Tftp ExamplesRetrieving message.txt Command Line Reference Cancel Notational ConventionsAdsl Commands Show Adsl ConfigurationSET Adsl Modulation Type G9922 Multimode Show Adsl StatisticsATM Commands Show ATM ConfigurationSET ATM Service Category UBR CBR Show ATM VCDhcp Commands Primary Wins server Secondary Wins serverIpaddress IP address of the Wins server Domain Domain name, a string of up to 31 charactersIpaddress IP address of the entry to enable or disable Ipaddress IP address of the entry to deleteDelete Dhcp Staticmap ipaddress Show Dhcp StaticmapShow Ethernet Statistics Ethernet CommandsShow Ethernet Address Filter Commands Number Position where new filter is to be addedNumber Number of the filter that is to be deleted Number Number of the filter to editFilter applies to both incoming and outgoing data default Number Number of the filter to copyDiscard the data Forward the data to the next filterApplied to TCP data default Applies to all dataApplies to UDP data Applies to TCP connection SYN dataEnable Ethernet multicast filtering Disable Ethernet multicast filteringMacaddress Source or destination MAC address Type Hexidecimal number indicating type of Ethernet frameGeneral Commands Hours Range 00 to Minutes SecondsReset Reset FactoryEnable Echo Server Disable Echo Server Enable Sysman Disable SysmanIP Commands General Show Statistics Ping ipaddress number sizeIP Routing Commands Show IP RouteEnable all module messages Logging and Internal Trace CommandsTaskName Module name as seen in Show LOG. Examples Dhcp NAT Network Address Translation Commands Enable NAT Disable NATUDP or TCP protocol Show IP NATPPP Commands Value Range 0-2147483647. DefaultValue Range 0-2147483647 milliseconds. Default Enable PPP Echo Request Disable PPP Echo RequestEnable PPP Phase Logging Disable PPP Phase Logging Enable PPP FSM Logging Disable PPP FSM LoggingSET PPP Local Username SET PPP Local Password Show PPP ConfigurationProfile Commands Enable Profile Disable ProfileShow Profiles Connect DisconnectSAR Commands Show SAR ConfigurationIndex Index of the VC taken from the SAR VC table Show SAR VC indexTftp Commands Enable Tftp Server Disable Tftp ServerTime Protocol Commands Enable Timeprotocol Disable TimeprotocolShow Timeprotocol Configuration TimeServer Address of the time serverRegulatory Information for Canada SpecificationsThis Section Specifications General SpecificationsSoftware and Firmware Specifications Declaration of Conformity Regulatory Information for the United StatesFCC Part 68 Notice Safety Notice Regulatory Information for Canada Safety Status TNV-3 Power ConsumptionRegulatory Information for the European Union EU Declaration of ConformityIndex Index