Marathon Computer AACC 2000 manual Sensor input connections, Module 1, 2

Page 16

Marathon Monitors Inc.

Sensor input connections

The connections for the various types of sensor input are shown below.

Thermocouple

Resistance

mA input

Volts or mV inputs

thermometer

 

 

 

V1

V+

v-

V1

V+

v-

V1

V+

v-

2.49Ω current sense resistor

V1

V+

v-

P V

Fig 1-7 Sensor input connections

PLUG-IN MODULE CONNECTIONS

Module 1, 2 and 3

Module positions 1, 2 and 3 are plug-in modules. They can be either two terminal modules of the types shown in Table 1-1, or four terminal modules of the types shown in Table 1-2.

The tables show the connections to each module and the functions that they can perform.

AACC 2000 Carbon

16

Nov. 1, 1997

 

 

Image 16
Contents Copyright Marathon Monitors INC Marathon Monitors Inc Mechanical Installation Safety Electrostatic discharge precautionsCleaning Electromagnetic compatibilitySafety Symbols WiringPower Isolation PersonnelOver-temperature protection Overcurrent protectionVoltage rating Conductive pollutionGrounding of the temperature sensor shield Installation requirements for EMCRouting of wires Environmental ratings Equipment ratingsElectrical safety GeneralMarathon Monitors Inc Installation Outline dimensions Model Outline dimensions Model 2000 controllerTo install the controller IntroductionController labels Unplugging and plugging-in the controllerRear terminal layouts Model Aacc 2000 rear terminal layoutMarathon Monitors Inc Sensor input connections Module 1, 2Two terminal modules SnubbersCOM Four terminal modulesDual output modules Connections for Process Value 3 in module position Connections for Process Value 2 PV2Communication module Wiring of 2-wire EIA-485 serial communications link EIA-485 wiringMarathon Monitors Inc Operation 26.0 Front Panel LAYOUTsButton or Name Explanation OP1OP2 SP2Alarms Basic operationOperating modes Automatic mode Output power demandHome display Display unitsManual Mode SetpointParameters and HOW to Access Them List header displaysMarathon Monitors Inc Parameter displays Parameter namesTo change the value of a parameter 1OFF ListOFF PID PID.1Fact STDPass Millivolt input Offset Name Description Prob Probe list Process FactorHydrogen or CO constant Name Description TunE DrADrA.t AdcPid PID list SEtRES HcbSetpoint list Input listCmS Comms list Output listInFo Information list Access List FF.OPAlarms Diagnostic alarms Display What it means What to do about it Shows2b Diagnostic alarms Access Levels Password entry Access list headerAccess to Read-only Configuration Configuration level Configuration passwordLevel selection Setting operator access to a parameter Edit levelReturning to Operator Level Hiding or revealing a complete listPromoting a parameter This sheet intentionally left blank Tuning Parameter Code Meaning or FunctionOne-shot Tuning How to tuneCalculation of the cutback values Typical automatic tuning cycleAdaptive tune Manual Tuning Setting the cutback values Proceed as followsIntegral action and manual reset Automatic droop compensation AdcName Description Values Mtr Motor list Min Max Default Motorized valve controlAdjusting the minimum on-time ‘mp.t’ Inertia and backlash settingsMarathon Monitors Inc Gain scheduling Enable in configuration levelSet the transfer point Configuration Selecting configuration level Press to enter configurationLeaving Configuration Level Changing the passwordsREU LIND1SA Enab SB.OPCMS RelyNone DIG YESPMV InSt Instrument configuration Name Description Values MeaningH2O SP.FFInput configuration Process value configCJC VAL.L Setpoint configurationVAL.H Table a Alarm types Value Alarm configuration ValuesAlarm Modes Digital input 2 configuration Action on contact closure Digital input 1 configuration Action on contact closureIMP Vflt Alarm relay configurationPflt Comms 1 module config Combining several digital events on to one output1A b C1 Module 1 configuration Module configCool 2A/b/C Module 2 configuration For ‘id’ = ‘LoG.i’ i.e logic input use the LA Conf’ list onDisplayed value low 3A/b/C Module 3 configuration SELC Module configuration Module configurationVAL.1 Point Custom LinearisationVAL.8 CAL Password configuration Exit Exit configurationDC Output Calibration User calibrationUser calibration User Calibration Enable Calibration Configuration ListUser Calibration Enable Exit configurationInput list header Offset calibrationCalibration type See table on the right for additional parameters Set OffsetTwo-point calibration Displayed ValueAdjust low-point calibration Select Low-point CalibrationAdjust High-point Calibration Select High-point CalibrationCalibration points and Calibration offsets Name Parameter description MeaningParameter Table Default HY1 Ssel FLT3 Marathon Monitors Inc AL1 Module 2A High Value VAL.1 101 Index Two-point calibration User calibration Aacc 2000 Carbon