Harmony House 802.11a manual Harmony Security Protocol, WEP Keys

Page 33

Configuration Parameters

33

WEP Keys

An 802.11a device with WEP enabled uses a WEP Key to encrypt and decrypt information. A user must manually enter the network’s WEP Keys on each 802.11a device. If the WEP Keys do not match on two radios, no data communication will take place between these devices.

A Harmony 802.11a network adapter can support up to four WEP Keys (all four Keys must have the same Key Size). A Harmony 802.11a adapter can decrypt information that was encrypted with any of its four WEP Keys, but it will only use the Default Key to encrypt outgoing information.

For 64-bit encryption, a WEP Key is 10 hexadecimal digits (0-9 and A-F); for 128-bit encryption, a WEP Key is 26 hexadecimal digits (0-9 and A-F); and for 152-bit encryption, a WEP Key is 32 hexadecimal digits (0-9 and A-F).

Note: When WEP is enabled, Proxim recommends that you configure all 802.11a devices in the Extended Service Set with the same WEP Keys in the same order (but the devices do not need to use the same default Key).

Harmony Security Protocol

The Harmony Security Protocol automates encryption management, assigning a unique and dynamic WEP Key to each user. The Harmony Security Protocol includes the following features:

Uses 152-Bit WEP Encryption

Generates a unique WEP Key for each user that is valid only for the current net- work session

Periodically renews the user’s Harmony session and assigns a new WEP Key without requiring any end user interaction

Incorporates the end user’s logon prompt into Microsoft Windows’ standard logon procedure on the client device

Each Harmony device plays a role in the Harmony Security Protocol: the AP Controllers maintain a database of user name and passwords to authenticate users; the Access Points block all network traffic to or from a client until after the user has been successfully authenticated by the Harmony System; and the Harmony client adapters include a software utility that incorporates the Harmony logon prompt into the standard Windows logon procedure.

When the Harmony Security Protocol is enabled on a client adapter, the user is prompted to enter his or her Harmony User Name and Password during boot up, either immediately before or after the Windows logon prompt (depending on the device configuration).

Once the user has been authenticated by the Harmony System, the 802.11a adapter receives a unique 152-bit WEP Key from the Harmony System, and it can begin to exchange data with the Ethernet network. Refer to the Harmony Access Point Controller User’s Guide for more information on the Harmony Security Protocol.

Image 33
Contents Users Guide Harmony 802.11a Network AdapterFCC Warning That the following harmonized standards have been applied Declaration of ConformityFor Indoor Use Only Table of Contents Index Introduction ChapterHarmony Family Product Package Harmony 8450 802.11a CardBus CardHarmony 8150 802.11a PCI Card System Requirements Overview of Country-Specific Features Pre-installation Considerations InstallationRegulatory Warnings FCC GuidelinesIndustry Canada Guidelines Windows ME and Windows 98 SE Installation CD Requirement802.11a CardBus Card Windows NT Laptops Require a Plug-and-Play UtilityWindows 98SE/ME/2000/XP Installation InstructionsPage Page Windows NT Page Harmony 802.11a PCI Card users Follow these steps Related Topics Upgrading to Version Ad Hoc Wireless TopologiesInfrastructure Connecting to a Single APRoaming Roaming Between Multiple APsGuidelines for Roaming Ieee 802.11a Specification Configuration Parameters802.11a Software Parameters Network ModePower Saving Mode 2X ModeRoaming For United States and Canada ChannelFor Europe For JapanSend Rate FragmentationFor Singapore Security Options WEP Encryption and AuthenticationWEP Keys Harmony Security ProtocolHarmony Security Protocol Guidelines 802.1xConfiguration Parameters Status Monitor Icon Harmony UtilityAssociation Information Configuration UtilityHarmony Utility Station Configuration Harmony Utility Harmony Utility Security WEP for Authentication and EncryptionPage Read Key File Format Harmony Security Protocol Page Page Page 802.1x Click the Wireless Networks tab Click the Authentication tabNetwork Traffic Statistics Send Receive 802.11a Networks Snoop Tool Packet Transmission Success Rate Version Information Troubleshooting How to Obtain Help with Your LAN InstallationCommon Installation Problems Adapter Inserted Before Running the Installation Program Windows 98/ME/2000/XP TroubleshootingAdapter Not Listed in Device Manager 802.11a Network Adapter Not Installed ProperlyConfiguring Networking Clients and Protocols Windows XP/2000Windows ME/98 SE Windows NT Uninstalling a Harmony 802.11a Network AdapterWindows 98/ME computers RangeWindows NT computers Windows 2000 computersCardBus Card LED Indicators Common Technical Support Questions Logon Access Point is out of range box and clickPassword so the Harmony logon Technical Specifications Technical SpecificationsGeneral Network InformationRadio EnvironmentalPhysical Ssid ParametersTechnical Support and Training Appendix BIndex Infrastructure Network Mode Ssid Throughput Topologies