Digital Networks North America DNswitch 800 manual IP Configuration, Parameter Default Description

Page 22

IP Configuration

Use the IP Configuration screen to set the bootup option, configure the Ethernet IP address for the switch, or set the number or concurrent Telnet sessions allowed. The screen shown below is described in the following table.

Figure 3-4. IP Configuration

Parameter	Default	Description
IP State	BootP-Get-IP	Specifies whether IP functionality is enabled via
		manual configuration, or set by Boot Protocol
		(BootP). Options include:
		BootP Get IP - IP is enabled but will not function
		until a BootP reply has been received. BootP
		requests will be periodically broadcast by the
		switch in an effort to learn its IP address. (BootP
		values include the IP address, default gateway,
		and subnet mask.)
		User-Configured - IP functionality is enabled
		based on the default or user specified IP
		Configuration.
IP Address	10.1.0.1	IP address of the switch you are managing. The
		switch supports SNMP over UDP/IP transport
		protocol. In this environment, all systems on the
		Internet, such as network interconnection devices
		and any PC accessing the switch (or running
		management software) are assigned an IP
		address. Valid IP addresses consist of four
		numbers, of 0 to 255, separated by periods.
		Anything outside of this format will not be
		accepted by the configuration program.
Subnet Mask	255.255.0.0	Subnet mask of the switch. This mask identifies
		the host address bits used for routing to specific
		subnets.
Gateway IP		Gateway used to pass trap messages from the
		switch to the management station. Note that the
		gateway must be defined if the management
		station is located in a different IP segment.
MAC Address		Physical address of the switch.
Number of Telnet	4	Sets the number of concurrent Telnet sessions
sessions		allowed to access the switch.

12 Configuring and Monitoring the Switch

DNswitch 800

Image 22

Contents Digital Networks Page DNswitch Web Management Guide Revision/Update InformationPage FCC Class B Certification USA Safety Compliance Underwriters Laboratories Compliance Statement Page Table of Contents Index Digital Networks WebView Description FeaturesSystem Requirements Conventions This guide uses the following user input conventionsSetting Up Web Management Setting an IP AddressSetting the Administrator Password Setting a Default GatewaySetting Trap Destinations Starting and Stopping Digital Networks WebView Enabling Web ManagementDigital Networks WebView User Interface Areas of the User InterfaceAreas of the User Interface Using Help Configuration OptionsConfiguring and Monitoring the Switch Screen HierarchySystem Information Parameter DescriptionSwitch Information Main BoardIP Configuration Parameter Default DescriptionSnmp Configuration Snmp CommunityTrap Managers Trap ManagersSecurity Configuration Change PasswordFirmware Upgrade Options Web Upload ManagementTftp Download Management Tftp Download ManagementConfiguration Upload Management Configuration Save and RestoreConfiguration Download Management Address Table Configuration 12. Address TableSTA Spanning Tree Algorithm Spanning Tree Information Spanning Tree14. STA Information Ports Spanning Tree Configuration Switch16. STA Configuration When the Switch Becomes Root STA Port Configuration EnabledConfiguring Bridge MIB Extensions Bridge CapabilityBridge Settings GmrpPort Priority Configuration PriorityPort Traffic Class Information 21. Port Traffic Class InformationVlan Management Vlan IDConfiguring Virtual LANs Vlan Basic InformationVlan Current Table 24. Vlan Current TableVlan Static List Vlan Static Table27. Vlan Static Table Port Assignment Vlan Static Membership by Port 28. Vlan Static Membership by PortVlan Port Configuration PvidConfiguring Igmp Igmp Multicast FilteringMulticast Router Port Information 31. Multicast Router Port InformationStatic Multicast Router Port Configuration 32. Static Multicast Router Port ConfigurationIgmp Member Port Table 33. Igmp Member Port TableIP Multicast Registration Table 34. IP Multicast Registration TablePort Menus Port InformationPort Configuration Directly to the switch when its buffers fill. BackPort Broadcast Storm Protect Configuration 37. Port Broadcast Storm Protect ConfigurationPort Security Configuration 38. Port Security ConfigurationUsing a Port Mirror for Analysis 39. Mirror Port ConfigurationPort Trunk Configuration 40. Port Trunk Configuration Port Statistics Etherlike StatisticsRmon Statistics 42. Rmon StatisticsBits but including FCS octets Configuring and Monitoring the Switch DNswitch Cannot Connect to the Switch TroubleshootingSystem is Disconnected from the Switch Can I Open More Than One Window for Same Switch? Frequently Asked QuestionsHow Do I Confirm a Successful Software Download? Index Vlan Page WM-DSA8G-00