Dell CPx H/CPx J Series, CPt V/CPt S Series manual Dimm a

￿￿￿￿￿￿￿￿￿￿￿￿￿￿

inner tabs	DIMM A
(2 per socket)	DIMM B

memory

module sockets (2)

￿￿￿￿￿￿￿4￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿#￿￿￿￿"￿#￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿"￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

1.Remove the main battery and secondary battery (if present).

2.Remove the memory module cover.

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿&

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿*￿3$,"￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿4￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿)￿￿￿￿￿(￿￿￿￿￿￿￿

3.To release a memory module from its socket, carefully spread apart the inner tabs of the memory module socket just far enough for the memory module to disengage from the socket. The module should pop up slightly (see Figure 8).

4.Lift the memory module out of its socket.

￿￿￿￿￿￿￿￿￿￿￿￿￿￿#￿￿￿￿"￿#￿￿￿￿￿￿

1.If you only have one memory module, install it in the DIMM A socket.

NOTES: 192-MB memory modules are designed for either the socket labeled DIMM A or the socket labeled DIMM B; they are not interchangeable. Be sure that the memory module is inserted with the double-stacked memory chips facing you. A 192-MB memory module inserted with the double-stacked memory chips facing down does not fit properly in the socket.

Memory modules are keyed, or designed to fit into their sockets, in only one direction. The slots on the system board are notched so that the mem- ory module can be firmly seated only one way.

support.dell.com Dell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual 13