Dell CPx H/CPx J Series, CPt V/CPt S Series manual 789

NOTE: The microprocessor shield brace may not be present on your system, if the brace is not present continue with step 6.

5.Remove the 4-mm screw that secures the microprocessor shield brace (see Figure 12).

6.Remove the microprocessor shield.

7.Rotate the arm of the thermal cooling assembly up and away from the microprocessor module.

￿￿￿￿￿￿￿￿/￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿"￿￿￿￿￿￿￿￿￿￿￿￿￿&

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿$￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿%￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

8.Use a microprocessor extractor tool to remove the microprocessor module.

The tool fits on the left side of the module aligned with white marks on the front and back edge of the processor board (see Figure 12).

￿￿￿￿￿￿￿￿￿￿￿￿￿￿#￿￿￿￿￿￿￿￿￿￿￿￿￿￿#￿￿￿￿￿

￿￿￿￿￿￿￿￿6￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿2￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿*￿￿￿￿￿%￿￿￿￿￿￿￿￿78￿￿￿￿￿￿￿￿9:;￿(￿￿￿&

￿￿￿￿￿<,￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿2￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

1.Align the microprocessor connector on the left side of the board and press down firmly on the metal plate that is directly over the connector.

When the microprocessor module is fully seated, all four corners are aligned to the same height. If one or more corners of the module are higher than the others, the module is not seated correctly.

2.To ensure the microprocessor module is fully seated, apply pressure over the corner without the mounting screw hole.

NOTE: If your system uses a microprocessor shield with the brace as shown in Figure 12, the 4-mm screw used in step 6 secures this corner.

3.Rotate the arm of the thermal cooling assembly into place.

4.Replace the microprocessor shield.

5.Replace the two 3-mm screws that secure the thermal cooling assembly arm and shield to the microprocessor module.

6.Replace the 4-mm screw securing the shield brace (if present).

7.Tighten the three captive screws on the corners of the shield to secure the microprocessor module and shield (see Figure 12).

support.dell.com Dell Latitude CPt V/CPt S Series and CPx H/CPx J Series Service Manual 19