Diamond Systems PR-Z32-E-ST VGA Accessory Board, PL5 pin no PL5 Signal J25 pin no J25 Signal

Page 71

26.VGA ACCESSORY BOARD

The Prometheus development kit ships with a PC/104 VGA module from Arcom Control Systems, model no. AIM-104-VGA-CRT-OEM. The Diamond Systems part no. for this board is ACC-VGA- 02.

The VGA board has several configuration jumpers, LK1 – LK3. Their functions are described in the board’s documentation. For proper operation with Prometheus, jumper LK1 must be out.

The VGA output connector on the Arcom board is a 16-pin connector labeled PL5, located on the left edge of the board. When used with the Diamond Systems panel board model PNL-Z32-E / EA, this connector connects to the 10-pin VGA input header J25 on the panel board using Diamond Systems cable no. 698013. The pinout of this cable is shown below. Each row represents one wire on the cable.

PL5 pin no.

PL5 Signal

J25 pin no.

J25 Signal

1

Red

1

Red

2

Red Return

2

Ground

3

Green

3

Green

4

Not connected

4

Ground

5

Blue

5

Blue

6

Green Return

6

Ground

7

Not connected

-

Not connected

8

Not connected

8

PCB shield

9

Blue Return

-

Not connected

10

Ground

-

Not connected

11

Ground

-

Not connected

12

H Sync

7

H Sync

13

Not connected

-

Not connected

14

V Sync

9

V Sync

15, 16

Not connected

-

Not connected

To connect PL5 directly to a VGA monitor with a high-density DB15 connector, use the multicolor ribbon cable supplied with the video board. This cable has the following pinout:

PL5 pin no.

DB15F pin no.

Signal

 

 

1

1

Red

 

 

2

6

Red Return

 

 

3

2

Green

 

 

4

4

No Function

 

 

5

3

Blue

 

 

6

7

Green Return

 

 

7

9

No Function

 

 

8

11

No Function

 

 

9

8

Blue Return

 

 

10

5

Ground

 

 

11

10

Ground

 

 

12

13

H Sync

 

 

13

12

No Function

 

 

14

14

V Sync

 

 

15

15

No Function

 

 

16

-

No Wire

 

 

 

 

Prometheus CPU User Manual V1.44

Page 71

Page 70 Page 72
Image 71
Page 70 Page 72
Contents Prometheus Table of Contents 22.4 22.2CPU DescriptionProcessor Section FeaturesSystem Features Digital I/O Counter/TimersAnalog Input Analog OutputPrometheus Board Drawing Cable B Main I/O Connector J3O Headers Cable aIR RX, IR TX Connector Part NumbersCOM1 COM4 LPT1Input Power J11 USB J5 Output Power J12Ethernet J4 Watchdog/Failsafe Features J6 Auxiliary Serial Port Connector J15IDE Drive J8 Floppy Drive J7Signal Name Definition Data Acquisition I/O Connector J14 Model PR-Z32-EA onlyJ2 PC/104 16-bit bus connector J1 PC/104 8-bit bus connector 11 PC/104 Bus ConnectorsCmos RAM Jumper ConfigurationJ10 System Configuration J6 Watchdog Timer & System Recovery CPU Chip Selects System FeaturesSystem Resources Console Redirection to a Serial Port Watchdog Timer Flash Memory Failsafe Mode / Bios RecoveryBackup Battery System ResetDOS BiosBios Settings Bios Download / Recovery Operating System Formatting Initial SetupDisk-On-Board Flash File Storage Life Cycle Management and Calculations Known LimitationsEthernet System I/OParallel Port Serial PortsInstalling an OS From a Floppy Drive onto a Flashdisk Module Booting to DOS From a Floppy DriveInstalling an OS from a Hard Disk onto a Flashdisk Module Data Acquisition Circuit LSB Data Acquisition Circuitry I/O MAPBase Address Base + Write Function Read FunctionAD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 Data Acquisition Circuit Register MapBase + Command RegisterRegister Bit Definitions AD9 AD8 Base + ReadValue = Base + 0 value + Base + 1 value Base + Write Not Used ReadBase + Read/Write Channel Register Base + Write Analog Input Gain STS Wait Dacbsy OVF Scanen Base + Read Analog Input StatusFT5 FT4 FT3 FT2 FT1 FT0 Base + Read/Write Interrupt / DMA / Counter ControlCKSEL1 CKFRQ1 CKFRQ0 Adclk Dmaen Tinte Dinte Ainte Base + Read/Write Fifo ThresholdFD5 FD4 FD3 FD2 FD1 FD0 Base + WriteDA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 Base + Read Channel and Fifo StatusBase + Read Analog Operation Status Base + Write DAC MSB + Channel NoDACH1 DACH0 DA9 DA8Dioctr = Base + Read / WriteBase + Read / Write Digital I/O Control Register Dioctr Dira Dirch Dirb DirclBase + Read/Write Counter/Timer D23 Base + Read/Write Counter/Timer D7Base + Read/Write Counter/Timer D15 Ctrno Latch Gtdis Gten Ctdis Cten Load CLR Base + Write Counter/Timer Control RegisterREV7 REV6 REV5 REV4 REV3 REV2 REV1 REV0 Base + Read Fpga Revision CodeData Acquisition Circuit Configuration Unipolar / Bipolar Inputs Analog Output ConfigurationSingle-ended / Differential Inputs Input Range Selection Analog Input Ranges and ResolutionInput Range Resolution 1 LSB OverviewPerforming AN A/D Conversion LSB = inpbase MSB = inpbase+1 Perform an A/D conversion on the current channelInput voltage = A/D value / 32768 * Full-scale input range 15.A/D SCAN, INTERRUPT, and Fifo Operation Ainte Scanen Prometheus A/D Operating ModesLOW, High LSB = Output voltage range Analog Output Ranges and ResolutionResolution DescriptionREF 1 LSB 16.4 D/A Conversion Formulas and TablesConversion Formulas for Bipolar Output Ranges Generating AN Analog Output 18.3 A/D full-scale Analog Circuit Calibration18.1 A/D bipolar offset 18.2 A/D unipolar offsetDigital I/O Operation Counter 1 Counting/Totalizing Functions COUNTER/TIMER OperationCounter 0 A/D Sample Control Counter Command SequencesCounter Outpbase+15,0x01 Outpbase+15,0x81 Data Acquisition Specifications Flashdisk Module ConfigurationUsing the Flashdisk with Another IDE Drive Power Supply23. I/O Panel Board USB a Panel Board I/O ConnectorsPanel Board Top Side / External Use I/O Connectors Location Type DescriptionJ12 pinout to/from DC/DC power supply Panel Board Power ConnectionsJ3 Pinout J5 USB J9 Pinout InstallationFlash Disk Programmer Board Cable Kit C-PRZ-KIT 25.I/O CablesPhoto No Cable No Description PL5 pin no DB15F pin no Signal VGA Accessory BoardPL5 pin no PL5 Signal J25 pin no J25 Signal Website information Prometheus Connector Manufacturer Manufacturer Part NoMounting Prometheus on a Baseboard LinksPage 28.PC/104 Mechanical Drawing

PR-Z32-E-ST, PR-Z32-EA-ST specifications

The Diamond Systems PR-Z32-EA-ST and PR-Z32-E-ST are pioneering solutions in the realm of embedded computing systems, designed to meet the challenging demands of various industrial applications. These boards harness advanced technologies and a comprehensive feature set to ensure exceptional performance, flexibility, and reliability.

At the heart of the PR-Z32 series is a robust processor architecture that combines efficiency with processing power. The systems are built around the Zynq-7000 SoC (System on Chip), which integrates a dual-core ARM Cortex-A9 processor with Xilinx FPGA technology. This hybrid architecture provides the ability to run complex algorithms and custom logic concurrently, making the boards ideal for applications requiring intense computational tasks such as image processing, data acquisition, and real-time control.

One of the main features of the PR-Z32-EA-ST and PR-Z32-E-ST is their versatility. Both variants support a wide range of I/O options, including USB, Ethernet, CAN, and serial interfaces. This range of connectivity allows for integrations with various sensors, actuators, and other peripheral devices, making it suitable for industrial automation, robotics, and IoT projects. The inclusion of multiple GPIO pins also enhances the capability of the boards to interface with additional hardware.

In terms of performance, the PR-Z32 series supports substantial amounts of on-board memory, which can be essential for applications requiring the storage and processing of large datasets. The configurations are often customizable, allowing users to select the appropriate amount of RAM and on-board flash memory for their specific applications.

Reliability is a critical characteristic of the Diamond Systems PR-Z32 series. The boards are built to withstand adverse environmental conditions, making them suitable for deployment in industrial environments. They are often designed to operate over a wide temperature range, ensuring functionality in both hot and cold climates. Additionally, the boards are compliant with various industry standards, assuring users of their robustness and durability.

Moreover, the PR-Z32-EA-ST and PR-Z32-E-ST support real-time operating systems (RTOS) and conventional operating systems such as Linux. This support provides developers with the flexibility to choose the best environment for their applications, whether they require real-time performance or full-fledged operating system features.

In conclusion, the Diamond Systems PR-Z32-EA-ST and PR-Z32-E-ST are formidable options for those seeking powerful, versatile, and reliable embedded computing solutions. With their advanced SoC architecture, flexible I/O options, extensive memory configurations, and environmental resilience, these boards are well-equipped to tackle the challenges of modern industrial applications.
Top Page Image Contents