Citizen Systems iDP-460 user manual Operation, Connecting AC Adapter

Page 20

iDP-460 User’s Manual

4. OPERATION

4.1 Connecting AC Adapter

(1)Turn off the Power switch.

(2)Connect the cable connector of the AC adapter to the power connector located on the back of the printer.

(3)In order to prevent disconnection of the cable connector, put it through a wire saddle, as shown in the figure below.

(4)Connect the AC power cord plug to a plug socket.

CAUTION : • Use only the specified AC adapter.

•Use a different AC power supply from one used for any noise-generating device.

•Do not use the accessory AC adapter for another device or application besides this equipment.

•When disconnecting the AC adapter, be sure to hold the AC adapter itself or the plug. Do not pull its cord.

•Pulling an AC adapter cord will damage it and may result in fire, electric shock, or snapping of the wire.

•If lightning is occurring in the area, disconnect the AC adapter from the plug socket and do not use the equipment. A lightning strike could result in fire or electric shock.

•Do not put the AC adapter cord near any thermal device. The coating of the power cord can melt, resulting in fire or electric shock.

•When the printer is not used for a long period of time, be sure to disconnect the AC adapter from the plug socket, for safety.

20

CITIZEN

Image 20

Contents Citizen Japan CBM Corporation Information Systems DivDeclaration of Conformity Important Safety Instructions Wichtige Sicherheitsanweisungen Sicherheitshinweis Citizen Safety Precautions Citizen Precautions for Installation Precautions for Handling Daily Maintenance Contents Appendix Einstellung DER DIP-SCHALTER Unpacking FeaturesOutline Basic Specifications Model ClassificationBasic Specifications Printing Position Paper SpecificationRecommended Paper Outer Appearance and Component Parts Connecting AC Adapter OperationConnecting Interface Cable Connecting Drawer Kick-Out ConnectorSetting the Cassette Ribbon Inserting the Paper Citizen How to Remove Remaining Paper Roll Removing Paper JamOperation Panel and Display of Error Details of ErrorsPrint Duty DIP Switch Setting Location of DIP SwitchDIP Switches Setting Parallel Interface SpecificationsConnector’s Pin Confuguration Input and Output Signals Input and Output SignalsElectrical Characteristics Timing Chart Data Receiving ControlSerial Interface Connector’s Pin Configuration DTRInput and Output Signals Data Configuration Error Detection BufferingRS-232C circuit Input RD, DSR Printer Side Host Side Drawer KICK-OUT Connector and Power Connector Specifications of Drawer Kick-Out Connector D-type OnlyConnector’s Pin Configuration Drive CircuitSpecifications of Power Supply Connector Maintenance and Service Command List Print Control FunctionsCommand Sets Command Details Description of ItemsDetails Can ALL 200,40ch 250,42chUS, SO, SI RS, US, SI Bell D-type Only ESC a nESC b n ESC cESC d 250, P-900R ESC e n 250, P-900RESC h n ESC ESC 200, P-250Character Codes Table 11.1International11.2Japanese 11.3International Character Codes TableAll Common Appendix 1. Block Diagram CPUAppendix 2. Outline Drawing German Vorsicht ZU Beachtende Sicherheitsmassregeln Warnung Vorsichtsmassregeln FÜR DIE Aufstellung Vorsichtsmassregeln FÜR DIE Handhabung Tägliche Wartung Betrieb Anschluß des NetzteilsAnschluß des Schnittstellenkabels Anschluß des Ausschubmechanismussteckers der GeldschubladeEinsetzen der Farbbandkassette Einlegen der Papierrolle Citizen Entfernen des restlichen Druckpapiers Beseitigung von PapierstausBedienfeld und Fehleranzeigelämpchen Druckvorgang Einstellung DER DIP-SCHALTER DIP-SchalterstellungDIP-Schalter-Tabelle Citizen