Citizen Systems iDP-460 user manual Drawer KICK-OUT Connector and Power Connector, Drive Circuit

Page 40

iDP-460 User’s Manual

8. DRAWER KICK-OUT CONNECTOR AND POWER CONNECTOR

8.1Specifications of Drawer Kick-Out Connector (D-type Only)

(1)Drawer kick-out drive signal

The pulses specified by the BELL command(07h) are output.(Approx. 200 ms)

(2)Electrical characteristics

1)Drive voltage: 24 V DC

2)Drive current: 0.8 A at maximum

8.1.1Connector’s Pin Configuration

No.

Signal

Function

1

FG

Frame Ground

2

DRAWER

Drawer drive signal

3

4

VDR

Drawer drive power

5

6

GND

Common ground on the circuit

Connector used

: TM5RJ3-66(HIROSE) or equivalent

Applicable connector : TM3P-66P(HIROSE) or equivalent

CAUTION : • No output is made while printing.

•A solenoid used for the drawer should be of 36 Ω or more. An output current should be kept below 0.8 A. Otherwise, there is a danger of trouble or burnout.

•This connector cannot be connected to a telephone line. Do not connect other than the solenoid.

8.1.2Drive Circuit

40

CITIZEN

Image 40

Contents Citizen Japan CBM Corporation Information Systems DivDeclaration of Conformity Important Safety Instructions Wichtige Sicherheitsanweisungen Sicherheitshinweis Citizen Safety Precautions Citizen Precautions for Installation Precautions for Handling Daily Maintenance Contents Appendix Einstellung DER DIP-SCHALTER Outline FeaturesUnpacking Basic Specifications Model ClassificationBasic Specifications Recommended Paper Paper SpecificationPrinting Position Outer Appearance and Component Parts Connecting AC Adapter OperationConnecting Interface Cable Connecting Drawer Kick-Out ConnectorSetting the Cassette Ribbon Inserting the Paper Citizen How to Remove Remaining Paper Roll Removing Paper JamOperation Panel and Display of Error Details of ErrorsPrint Duty DIP Switch Setting Location of DIP SwitchDIP Switches Setting Connector’s Pin Confuguration SpecificationsParallel Interface Input and Output Signals Input and Output SignalsElectrical Characteristics Timing Chart Data Receiving ControlSerial Interface Connector’s Pin Configuration DTRInput and Output Signals Data Configuration Error Detection BufferingRS-232C circuit Input RD, DSR Printer Side Host Side Drawer KICK-OUT Connector and Power Connector Specifications of Drawer Kick-Out Connector D-type OnlyConnector’s Pin Configuration Drive CircuitSpecifications of Power Supply Connector Maintenance and Service Command List Print Control FunctionsCommand Sets Command Details Description of ItemsDetails Can ALL 200,40ch 250,42chUS, SO, SI RS, US, SI Bell D-type Only ESC a nESC b n ESC cESC d 250, P-900R ESC e n 250, P-900RESC h n ESC ESC 200, P-250Character Codes Table 11.1International11.2Japanese 11.3International Character Codes TableAll Common Appendix 1. Block Diagram CPUAppendix 2. Outline Drawing German Vorsicht ZU Beachtende Sicherheitsmassregeln Warnung Vorsichtsmassregeln FÜR DIE Aufstellung Vorsichtsmassregeln FÜR DIE Handhabung Tägliche Wartung Betrieb Anschluß des NetzteilsAnschluß des Schnittstellenkabels Anschluß des Ausschubmechanismussteckers der GeldschubladeEinsetzen der Farbbandkassette Einlegen der Papierrolle Citizen Entfernen des restlichen Druckpapiers Beseitigung von PapierstausBedienfeld und Fehleranzeigelämpchen Druckvorgang Einstellung DER DIP-SCHALTER DIP-SchalterstellungDIP-Schalter-Tabelle Citizen