Citizen Systems iDP-460 user manual Serial Interface, Specifications

Page 34

iDP-460 User’s Manual

7. SERIAL INTERFACE

7.1Specifications

(1)Synchronous system: Asynchronous

(2)Baud rate: 150, 300, 600, 1,200, 2,400, 4,800, 9,600, or 19,200 bps (User selectable)

(3)Configuration of one word

•Start bit	: 1 bit
•Data bits	: 7 or 8 bits (User selectable)
•Parity bit	: Odd, even, or none (User selectable)
•Stop bit	: 1 bit or more

(4)Signal polarity RS-232C

•Mark	=	Logic "1"	(-3 V to -12 V)
•Space	=	Logic "0"	(+3 V to +12 V)

(5)Received data (RD signal) RS-232C

•Mark = 1

•Space = 0

(6)Reception control (DTR signal) RS-232C

•Mark	: Data transfer disabled
•Space	: Data transfer enabled

(7)Transmission control (TD signal) •Status transmission

P-250	=	Transmits "A"(41h)
P-900R	=	Transmits "H"(48h)

•Printer state transmission

Transmits the data indicating the 1-byte state. (See 10. PRINT CONTROL FUNCTIONS)

34

CITIZEN

Image 34

Contents Citizen Japan CBM Corporation Information Systems DivDeclaration of Conformity Important Safety Instructions Wichtige Sicherheitsanweisungen Sicherheitshinweis Citizen Safety Precautions Citizen Precautions for Installation Precautions for Handling Daily Maintenance Contents Appendix Einstellung DER DIP-SCHALTER Outline FeaturesUnpacking Basic Specifications Model ClassificationBasic Specifications Recommended Paper Paper SpecificationPrinting Position Outer Appearance and Component Parts Connecting AC Adapter OperationConnecting Interface Cable Connecting Drawer Kick-Out ConnectorSetting the Cassette Ribbon Inserting the Paper Citizen How to Remove Remaining Paper Roll Removing Paper JamOperation Panel and Display of Error Details of ErrorsPrint Duty DIP Switch Setting Location of DIP SwitchDIP Switches Setting Connector’s Pin Confuguration SpecificationsParallel Interface Input and Output Signals Input and Output SignalsElectrical Characteristics Timing Chart Data Receiving ControlSerial Interface Connector’s Pin Configuration DTRInput and Output Signals Data Configuration Error Detection BufferingRS-232C circuit Input RD, DSR Printer Side Host Side Connector’s Pin Configuration Drawer KICK-OUT Connector and Power ConnectorSpecifications of Drawer Kick-Out Connector D-type Only Drive CircuitSpecifications of Power Supply Connector Maintenance and Service Command List Print Control FunctionsCommand Sets Command Details Description of ItemsDetails Can ALL 200,40ch 250,42chUS, SO, SI RS, US, SI Bell D-type Only ESC a nESC b n ESC cESC d 250, P-900R ESC e n 250, P-900RESC h n ESC ESC 200, P-250Character Codes Table 11.1International11.2Japanese 11.3International Character Codes TableAll Common Appendix 1. Block Diagram CPUAppendix 2. Outline Drawing German Vorsicht ZU Beachtende Sicherheitsmassregeln Warnung Vorsichtsmassregeln FÜR DIE Aufstellung Vorsichtsmassregeln FÜR DIE Handhabung Tägliche Wartung Betrieb Anschluß des NetzteilsAnschluß des Schnittstellenkabels Anschluß des Ausschubmechanismussteckers der GeldschubladeEinsetzen der Farbbandkassette Einlegen der Papierrolle Citizen Entfernen des restlichen Druckpapiers Beseitigung von PapierstausBedienfeld und Fehleranzeigelämpchen Druckvorgang Einstellung DER DIP-SCHALTER DIP-SchalterstellungDIP-Schalter-Tabelle Citizen