CBM America CBM-710, CBM-750, CBM-720, CBM-730 manual Dtr

Page 32

CBM-710/720/730/750 User ’s Manual

9.2 Connector Pin Assignment

Signal	Return		Signal		Direction			Current
Signal	Signal		Signal		Host/	Function	RS-232C	Current	TTL
Pin	Signal		Name		Host/	Function	RS-232C	Loop	TTL
Pin	Pin		Name		Printer			Loop
	Pin				Printer
1			FG			Safety Ground	O

7			GND			Signal Ground	O

3			RD		→	Received Data	O
3			RD			Received Data	O

20			DTR		←	Printer BUSY Signal	O
20			DTR			Printer BUSY Signal	O

2	22		TD		←	Transmitted Date	O	O
2	22		TD			Transmitted Date	O	O

11			PE		←	Paper End Signal			O
11			PE			Paper End Signal			O

12					←	Printer ALARM Signal	O
			FAULT		←
			FAULT

13	14		DTR		←	Printer BUSY Signal		O
13	14		DTR			Printer BUSY Signal		O

18	16		RD		→	Received Data		O
18	16		RD			Received Data		O

23					→	Printer RESET Signal			O
			RESET		→
			RESET


Notes:	[1] The signals for RS-232C use are based on EIA RS-232C level.

[2]The loop current for Current Loop signal use should be restrict ed within the range of 10 to 20mA.

[3]Please always maintain the "mark state", when received data are not being transferred.

[4]The assignment of RS-232C/Current loop/TTL can be performed with the preset jumper (Refer to 10. Slide Switch Setting).

Compatible Connector (D-Sub connector) :

*Printer:	17LE-13 250	(AMPHENOL or equivalent)
*Cable Side:	17JE-23 250	(AMPNENOL or equivalent)

26

CITIZEN

Image 32

Contents Page Declaration of Conformity Important Safety Instructions Sicherheitshinweis Contents 11.1 Introduction FeaturesAccessories Type Classifications CBM-710 23 RSpecifications General SpecificationsCBM-710 CBM-720 Paper Specifications Print FormatBlock Diagram External Appearance and Pars Descriptions CBM-710 External AppearanceCBM-720 External Appearance Front ViewCBM-730 External Appearance CBM-750 External Appearance Part Descriptions Setting and Removing the Paper and Ribbon Covers OperationOpening and Closing the Cutter Unit CBM-720. CBM-750 Installing the Cassette Ribbon Installing and Changing the Paper Installing the PaperCitizen Citizen Procedures for Actuating the Self Print Function Self Print FunctionPaper End Detector Changing the PaperInstallation of the CBM-750 Clearing the Input Buffer Input Buffer BACK-UP FunctionInput Buffer Back-up Parallel Interface SpecificationsConnector Pin Assignment Description of Input/Output Signals Input/Output SignalsElectrical Characteristics Timing Chart Serial Interface DTR Description of Input/Output Signals Error Detection Data CompositionData Receiving Control BufferingOutput DTR, TD Ready Setting DIP Switch DS1 Function SelectionDIP Switch DS2 Serial interface specifications only Slide Switch Setting Serial interface specifications only DIP Switch and Slide Switch LocationsPrint Control Functions Control CodesEnlarged character command Input Data FormatsEnlarged character cancel command Paper feed commandPrint command Clear commandBuzzer Command Initial Set CommandInverted character command Underline Command Graphic Command Graphic Type OnlyPin 13 1/9 inch Line Feed Pitch Set Command Graphic Type14 2/9 inch Line Feed Pitch Set Command Graphic Type Form Feed Command Skip Perforation Cancel Command 2nd byte 4EH 3rd byte N7 N6 N5 N4 N3 N2 N1 Binary digitalFull Cut Command 1st byte Character Code Tables International Character CodesIndividual Country Character Codes Maintenance Maintenance ProceduresExterior InteriorExternal Dimensions CBM-710CBM-720 Paper Winder Unit AW-2 CBM-730 CBM-750 Information Systems Division Head Office