DFI 40800950 manual Hardware Installation Wake-On-Ring Connector, Ground RI#

Page 34

Hardware Installation

2.7.16 Wake-On-Ring Connector

The Wake-On-Ring connector is used to connect to an internal modem card that has the same connector. It will allow the system that is in the Suspend mode or Soft Power Off mode to wake-up/ power-on to respond to calls coming through the internal modem card.

To use this function, connect one end of the cable (that came with the card) to the card’s wake-on-ring connector and the other end to location J19 on the system board.You must also enable the “Resume on Ring” field in the Power Management Setup of the BIOS.

If you are using an external modem, the ring-on function will come through the serial port where the external modem is connected.

Function

1Ground

2 RI#

Image 34

Contents PC64 40800950Trademarks CopyrightAll Rights Reserved FCC and DOC Statement on Class B Table of Contents Appendix C Troubleshooting Appendix a Using the Suspend to RAM FunctionAppendix B System Error Messages Supported SoftwaresFeatures Features and SpecificationsIntroduction ATX Double Deck Ports PC 99 color-coded connectors Onboard PCI Audio Features Aureal AU8810Expansion Slots IrDA Interface ConnectorsPCI Bus Master IDE Controller USB PortsDesktop Management Interface DMI System Health Monitor FunctionsIntelligence Automatic CPU/Chassis Fan OffWake-On-Ring Dual Function Power ButtonRTC Timer to Power-on the System Wake-On-LAN ReadyYear 2000 Compliant AC Power Failure RecoverySupports hardware Y2K function Package Checklist Virus ProtectionHardware Installation System Board LayoutSystem Memory Important Installation Instructions Determining the Maximum System Memory SizeHardware Installation Installing the Rimmtm Module Processor Installation Installing the ProcessorRemoving the Processor Slide Slit URM’s tabSlide Tab Jumper Settings for Clearing Cmos Data Type Y and press Enter Jumper Settings for Wake-On-Keyboard/ Wake-On-MouseWake-On-Keyboard/Wake-On-Mouse Jumper JP1 Default On DisableSystem’s Beep Message Output Select Jumper JP8 Serial Ports Ports and Connectors2 PS/2 Mouse and PS/2 Keyboard Ports Hardware Installation Parallel Port Floppy Disk Drive ConnectorConnecting the IDE Disk Drive Cable IDE Disk Drive ConnectorConnecting the Floppy Disk Drive Cable Cable aligned with pin 1 of the drive edge connectorsAdding a Second IDE Disk Drive Universal Serial Bus PortsHardware Installation IrDA Connector GroundChassis Fan Connector Hardware Installation CPU Fan ConnectorPin Function Ground On/Off Sense Hardware Installation Second Chassis Fan Connector Thermal Sensor ConnectorLine-out Jack J8 Lime Hardware Installation Game/MIDI PortAudio Jacks Line-in Jack J12 Light BluePin Function Left audio channel Ground Hardware Installation Internal Audio ConnectorsVideo-In, AUX-In and CD-In Modem-out from modem Ground Modem-in to modemHardware Installation Wake-On-LAN Connector Hardware Installation Wake-On-Ring Connector Ground RI#Hardware Installation Chassis Open Connector Ground Chassis signal +5VPCI Standby Power LED Hardware Installation RIMM/PCI Standby Power LEDRimm Standby Power LED 3VSB Standby for PCI jumper JP7Ground +5V Hardware Installation Power Connector+12V +5V Hardware Installation Front Panel LEDs and Switches HD-LED When you press Del, the main menu screen will appear Award Bios Setup UtilityStandard Cmos Features Basic Input/Output SystemTime DateIDE HDD Auto Detection Capacity Access ModeIDE Primary/Secondary Master/Slave Drive a and Drive BExtended Memory Halt OnBase Memory Total MemoryAward Bios Setup Utility Advanced Bios Features Virus WarningCPU L2 Cache ECC Checking Quick Power On Self TestCPU L1 Cache and CPU L2 Cache Processor Serial NumberTypematic Rate Setting Boot Up Floppy SeekBoot Up NumLock Status Typematic Delay MsecOS Select for Dram 64MB Security OptionHDD S.M.A.R.T. Capability Dram Data Integrity Mode Award Bios Setup Utility Advanced Chipset FeaturesRimm Module Used Delayed Transaction System Bios CacheableVideo Bios Cacheable Video RAM CacheableOn-Chip Primary PCI IDE and On-Chip Secondary PCI IDE Award Bios Setup Utility Integrated PeripheralsIDE Primary Master/Slave PIO and IDE Secondary Master/Slave USB Keyboard Support IDE HDD Block ModeUSB Controller Init Display FirstKeyboard/Mouse Power On Onboard Serial Port 1 and Onboard Serial Port UART2 Mode SelectOnboard FDC Controller RxD, TxD ActiveEPP Mode Select IR Transmission DelayParallel Port Mode ECP Mode Use DMAAcpi Function Power Management SetupAcpi Suspend Type HDD Power Down Power ManagementSuspend Mode Video Off MethodResume On Ring Soft-Off by PWR-BTTNResume on PCI Event Resume On LANDate of Month Alarm Resume On AlarmTime hhmmss Alarm Reset Configuration Data Award Bios Setup Utility 6 PnP/PCI ConfigurationsResources Controlled By PCI/VGA Palette Snoop SpecificationIRQ Resources PCI IRQ AssignmentThis field shows the voltage of the processor Award Bios Setup Utility System Health Monitor+1.5V, +3.3V, +5V, +12V, -12V, Vbat V and 5VSB CPU Clock Ratio Award Bios Setup Utility CPU Frequency ControlCPU Host/PCI Clock Method Load Fail-Safe DefaultsSpread Spectrum Award Bios Setup Utility Load Optimized Defaults Set Supervisor PasswordSave & Exit Setup Award Bios Setup Utility Set User PasswordExit Without Saving Supported Softwares Desktop Management Interface DMIRunning the DMI Utility Supported Softwares Using the DMI Utility Edit DMILoad DMI File Supported Softwares Add DMISave DMI File Intel 820 INF Update Utility for Windows 95/98 Hardware Doctor UtilitySound Driver IDE, USB and Firmware Hub Patch Utility for IntelSoftware License Agreement screen will appear. Click Yes Aureal Vortex Player for Windows 95/98 Intel Ultra ATA Storage Device for Windows 98/NT Drivers and Utilities Installation NotesMicrosoft DirectX 6.1 for Windows 95/98 Supported Softwares Using the Suspend to RAM Function Using the Suspend to RAM FunctionUsing the Suspend to RAM Function Using the Suspend to RAM Function Using the Suspend to RAM Function Cmos battery is no longer functional. It should be replaced Error MessagesSystem Error Message Post BeepFloppy Disks fail Keyboard error or no keyboard presentBios ROM checksum error System halted Hard Disks failTroubleshooting Troubleshooting ChecklistMonitor/Display Power Supply Floppy DriveTroubleshooting Hard Drive Hard disk failureKeyboard Troubleshooting Serial PortSystem Board