DFI 40800950 manual Halt On, Base Memory, Extended Memory, Total Memory

Page 43

Award BIOS Setup Utility

Halt On

This category determines whether the system will stop if an error is detected during power up.The default setting is All Errors.

No Errors The system boot will not stop for any errors detected. All Errors The system boot will stop whenever the BIOS detects

a non-fatal error.

All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors.

All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key The system boot will not stop for a disk or keyboard error; it will stop for all other errors.

Base Memory

Displays the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512K for systems with 512K memory installed on the motherboard or 640K for systems with 640K or more memor y installed on the motherboard.

Extended Memory

Displays the amount of extended memory detected during boot-up.

Total Memory

Displays the total memory available in the system.

3

43

Image 43

Contents 40800950 PC64Trademarks CopyrightAll Rights Reserved FCC and DOC Statement on Class B Table of Contents Supported Softwares Appendix a Using the Suspend to RAM FunctionAppendix B System Error Messages Appendix C TroubleshootingFeatures Features and SpecificationsIntroduction ATX Double Deck Ports PC 99 color-coded connectors Onboard PCI Audio Features Aureal AU8810Expansion Slots USB Ports ConnectorsPCI Bus Master IDE Controller IrDA InterfaceAutomatic CPU/Chassis Fan Off System Health Monitor FunctionsIntelligence Desktop Management Interface DMIWake-On-LAN Ready Dual Function Power ButtonRTC Timer to Power-on the System Wake-On-RingYear 2000 Compliant AC Power Failure RecoverySupports hardware Y2K function Virus Protection Package ChecklistSystem Board Layout Hardware InstallationSystem Memory Determining the Maximum System Memory Size Important Installation InstructionsHardware Installation Installing the Rimmtm Module Installing the Processor Processor InstallationSlide Slit URM’s tab Removing the ProcessorSlide Tab Jumper Settings for Clearing Cmos Data Type Y and press Enter Jumper Settings for Wake-On-Keyboard/ Wake-On-MouseWake-On-Keyboard/Wake-On-Mouse Jumper JP1 Default On DisableSystem’s Beep Message Output Select Jumper JP8 Serial Ports Ports and Connectors2 PS/2 Mouse and PS/2 Keyboard Ports Floppy Disk Drive Connector Hardware Installation Parallel PortCable aligned with pin 1 of the drive edge connectors IDE Disk Drive ConnectorConnecting the Floppy Disk Drive Cable Connecting the IDE Disk Drive CableUniversal Serial Bus Ports Adding a Second IDE Disk DriveGround Hardware Installation IrDA ConnectorChassis Fan Connector Hardware Installation CPU Fan ConnectorPin Function Ground On/Off Sense Thermal Sensor Connector Hardware Installation Second Chassis Fan ConnectorLine-in Jack J12 Light Blue Hardware Installation Game/MIDI PortAudio Jacks Line-out Jack J8 LimeModem-out from modem Ground Modem-in to modem Hardware Installation Internal Audio ConnectorsVideo-In, AUX-In and CD-In Pin Function Left audio channel GroundHardware Installation Wake-On-LAN Connector Ground RI# Hardware Installation Wake-On-Ring ConnectorGround Chassis signal +5V Hardware Installation Chassis Open Connector3VSB Standby for PCI jumper JP7 Hardware Installation RIMM/PCI Standby Power LEDRimm Standby Power LED PCI Standby Power LEDGround +5V Hardware Installation Power Connector+12V +5V Hardware Installation Front Panel LEDs and Switches HD-LED Basic Input/Output System Award Bios Setup UtilityStandard Cmos Features When you press Del, the main menu screen will appearTime DateIDE HDD Auto Detection Drive a and Drive B Access ModeIDE Primary/Secondary Master/Slave CapacityTotal Memory Halt OnBase Memory Extended MemoryVirus Warning Award Bios Setup Utility Advanced Bios FeaturesProcessor Serial Number Quick Power On Self TestCPU L1 Cache and CPU L2 Cache CPU L2 Cache ECC CheckingTypematic Delay Msec Boot Up Floppy SeekBoot Up NumLock Status Typematic Rate SettingOS Select for Dram 64MB Security OptionHDD S.M.A.R.T. Capability Dram Data Integrity Mode Award Bios Setup Utility Advanced Chipset FeaturesRimm Module Used Video RAM Cacheable System Bios CacheableVideo Bios Cacheable Delayed TransactionOn-Chip Primary PCI IDE and On-Chip Secondary PCI IDE Award Bios Setup Utility Integrated PeripheralsIDE Primary Master/Slave PIO and IDE Secondary Master/Slave Init Display First IDE HDD Block ModeUSB Controller USB Keyboard SupportKeyboard/Mouse Power On RxD, TxD Active UART2 Mode SelectOnboard FDC Controller Onboard Serial Port 1 and Onboard Serial PortECP Mode Use DMA IR Transmission DelayParallel Port Mode EPP Mode SelectAcpi Function Power Management SetupAcpi Suspend Type Video Off Method Power ManagementSuspend Mode HDD Power DownResume On LAN Soft-Off by PWR-BTTNResume on PCI Event Resume On RingDate of Month Alarm Resume On AlarmTime hhmmss Alarm Reset Configuration Data Award Bios Setup Utility 6 PnP/PCI ConfigurationsResources Controlled By PCI IRQ Assignment SpecificationIRQ Resources PCI/VGA Palette SnoopThis field shows the voltage of the processor Award Bios Setup Utility System Health Monitor+1.5V, +3.3V, +5V, +12V, -12V, Vbat V and 5VSB CPU Clock Ratio Award Bios Setup Utility CPU Frequency ControlCPU Host/PCI Clock Method Load Fail-Safe DefaultsSpread Spectrum Set Supervisor Password Award Bios Setup Utility Load Optimized DefaultsSave & Exit Setup Award Bios Setup Utility Set User PasswordExit Without Saving Supported Softwares Desktop Management Interface DMIRunning the DMI Utility Edit DMI Supported Softwares Using the DMI UtilityLoad DMI File Supported Softwares Add DMISave DMI File Hardware Doctor Utility Intel 820 INF Update Utility for Windows 95/98Sound Driver IDE, USB and Firmware Hub Patch Utility for IntelSoftware License Agreement screen will appear. Click Yes Aureal Vortex Player for Windows 95/98 Intel Ultra ATA Storage Device for Windows 98/NT Drivers and Utilities Installation NotesMicrosoft DirectX 6.1 for Windows 95/98 Supported Softwares Using the Suspend to RAM Function Using the Suspend to RAM FunctionUsing the Suspend to RAM Function Using the Suspend to RAM Function Using the Suspend to RAM Function Post Beep Error MessagesSystem Error Message Cmos battery is no longer functional. It should be replacedHard Disks fail Keyboard error or no keyboard presentBios ROM checksum error System halted Floppy Disks failTroubleshooting Troubleshooting ChecklistMonitor/Display Floppy Drive Power SupplyHard disk failure Troubleshooting Hard DriveKeyboard Troubleshooting Serial PortSystem Board