Hand Held Products Dolphin 7450, Dolphin 7400 manual DetectoidCE

Page 23

DetectoidCE

After running DetectoidPC, start Detectoid CE on the Dolphin terminal selecting Start>Programs>HHP>DetectoidCE.

DetectoidCE will attempt to find the connection with the PC. If successful, the discovered settings will be saved and the Communications Properties Launch window shown below will then display on your Dolphin. The default is Start ActiveSync when the unit is docked or connected. By choosing the default, ActiveSync will start automatically when the terminal is connected via a powered serial cable or docked in a powered HomeBase/IntelliBase. If you select Do not automatically start ActiveSync, you must manually start ActiveSync on the Dolphin terminal to establish communications (see Chapter 6).

If you want to go back and change the settings later, select Start>Settings>Control Panel>Communication Properties and select the Launch tab.

Once the communications parameters have been detected and configured, the status indicator will change to Success. Verify that the ActiveSync settings are correct, then click save to transfer those settings to ActiveSync.

2 - 9

Image 23

Contents Dolphin 7400/7450 Hand Held Computer Disclaimer PatentsTrademarks Table of Contents Using the Dolphin 7400/7450 Dolphin QuadCharger 11-2 Introduction Additional FeaturesBatch Terminals Required Safety LabelsIf Your Dolphin 7400/7450 has a Radio Canadian Compliance FCC Compliance Dolphin 7400/7450 Batch TerminalDolphin 7400/7450 RF Terminal with Cisco Parameter Specification Regulatory and Safety Agency ApprovalsTTE Dolphin 7400/7450 RF Cisco 352 R&TTE Compliance StatementMicrowaves Care and Cleaning of the DolphinBatteries Page Dolphin 7400 Models and Options Accessories for the Dolphin 7400/7450Getting Started Unpack the Carton and Check Its Contents Bar Code Symbologies SupportedLaser Engine Options and Symbologies Supported Using Dolphin 7400/7450 for the First TimeTurning the Dolphin On And Off For the First Time Charging the Main Battery and Backup BatteryRemoving the Battery Pack Installing the Battery PackDo not Press ANY Keys While the Terminal is Booting UP Waking the Dolphin From Sleep ModeStylus Properties Screen Setting the Date/Time Using DetectoidPC and DetectoidCE Setting Up Communications with DetectoidInstalling DetectoidPC Page DetectoidCE Touchscreen-equipped terminals Configuring the ModemVerifying that Dolphin 7400/7450 is Working Properly Terminals without touchscreens Resetting the Dolphin Cold BootResetting the Dolphin Warm Boot Page Dolphin 7400/7450 Overview System FeaturesVGA Display Front Panel FeaturesLEDs Keyboard Audio SignalsON/SCAN Key Cursor KeysImage Engine Back Panel FeaturesDolphin Hand Strap Battery WellBattery Charging Contacts Laser EngineBumpers Communication Managing Battery Power PowerLowBatt=dword19 Setting Critical and Low Battery PointsUsing the Power Control Panel CriticalBatt=dwordaStoring Batteries Charging the Battery PackServicing the Battery Pack Using the Battery Conditioning UtilityVia the Touch Screen Using the Dolphin 7400/7450Using the Image Reader Entering DataCapturing Images Linear bar code 2D Matrix symbolReading a Bar code Omni-Directional Scanning OptionsSoftware Communication Programs Communication MediaKeyboards Using the Special KeysTo Use This Cursor Key Press Description Using the Cursor KeysOther Special Keys Using the Modifier KeysKey Combinations Navigating the KeyboardUsing the Modem Dolphin 7400/7450 RF Terminal Client Utilities for the Cisco Dsss 802.11b Radio Configuring The Dolphin 7400/7450 RF TerminalConfiguring the Cisco Dsss Wlan Radio To Configure the Radio Card Customizing the ActiveSync Remote Icon Host ConnectivityPage Ir/IrDA Optical Communications Power ConditioningDolphin Charging/Communication Cradles Hub of the SystemOrange LED HomeBase/IntelliBase/USB HomeBaseGreen LED Data is being sent from the Dolphin HomeBase Comm LED Description Red LED AUX Battery LED Description Orange LEDIntelliBase+ Green LEDHomeBase/IntelliBase Back PanelIntelliBase+ Bottom Panel of HomeBase/IntelliBase/IntelliBase+ USB HomeBasePowering the Dolphin Terminal Deep-Cycling Batteries Setting Up For CommunicationsCharging Additional Battery Packs in the IntelliBase+ Installing The Charging/Communication CradleIBM AT DB9 IBM XT Select StartSettingsControl PanelCommunications Properties Configuring the Dolphin Terminal for CommunicationsPage Setting Up For Communications With The USB HomeBase Page Communicating with the Dolphin Terminal Wall Mounting Mounting the HomeBase/IntelliBase/USB HomeBaseDesk Mounting Page Top Panel Dolphin QuadChargerDolphin QuadCharger Parts and Function Charging Batteries In The QuadCharger Setting Up The QuadChargerSupplying Power To The QuadCharger Inserting and Removing Battery PacksStatus LED DescriptionProblem Issue TroubleshootingDolphin Mobile Charging/Communication Cradles Front Panel Mobile IntelliBase and Mobile Base Parts and FunctionsDolphin Mobile IntelliBase/Mobile Base Mounting Bracket Power Supply RS-232 Connector Locking Lever RS-232 Charging a Dolphin Terminal Bottom Panel of Mobile IntelliBase/Mobile BaseMounting the Mobile IntelliBase Spring Arm Assembly Installing The Dolphin Mobile IntelliBaseInstalling The Dolphin Mobile Base Setting the Baud Rate Select StartSettingsControl PanelCommunication Settings Configuring the Dolphin TerminalDeveloping Applications Page How Problems Should Be Handled Warranty, Support and ServiceLimited Warranty Locations How To Extend Your WarrantyReturn Information Europe, Middle East, and Africa Technical AssistanceAssistance Online North America/CanadaPage Press Appendix aWindows Keyboard Shortcuts Key Combination Function/Special Character Using the Modifier KeysKey Alpha/Numeric Keyboard Red key + T Red key + U Red key + W Red key + Y Key Numeric/Alpha Key/Key Combinations Function/Special Characters ALT + 3 + Key Full Alpha NumericF12 Red key + P F16 Red key + Q F17 Hold the ALT key down as you type in the numbers HHP, Inc