Hand Held Products Dolphin 7400 USB HomeBase, Bottom Panel of HomeBase/IntelliBase/IntelliBase+

Page 56

USB HomeBase

USB Connector

Power Supply

Connector

Rear View of Dolphin USB HomeBase

There is a 5V DC power supply connector and a USB connector:

Power supply connector Use this connector to attach a power supply to the HomeBase. The power supply provides 5V DC input for communications and battery charging.

USB Communications Port Use a USB full-speed detachable cable to connect this downstream device port to an upstream USB Host or Hub. The USB HomeBase is USB 1.3 compliant.

Bottom Panel of HomeBase/IntelliBase/IntelliBase+

A Baud Rate switch used to select the communication baud rate is located on the bottom of the HomeBase, IntelliBase and IntelliBase+. The Baud Rate Switch on the HomeBase is a three-position switch; four-position on the IntelliBase and IntelliBase+. Switch position and the corresponding baud rates are shown in the charts below.

The USB HomeBase does not require a baud rate switch.

6 - 6

Image 56

Contents Dolphin 7400/7450 Hand Held Computer Disclaimer PatentsTrademarks Table of Contents Using the Dolphin 7400/7450 Dolphin QuadCharger 11-2 Additional Features IntroductionRequired Safety Labels Batch TerminalsIf Your Dolphin 7400/7450 has a Radio Canadian Compliance FCC Compliance Dolphin 7400/7450 Batch TerminalDolphin 7400/7450 RF Terminal with Cisco Regulatory and Safety Agency Approvals Parameter SpecificationDolphin 7400/7450 RF Cisco 352 R&TTE Compliance Statement TTEMicrowaves Care and Cleaning of the DolphinBatteries Page Dolphin 7400 Models and Options Accessories for the Dolphin 7400/7450Getting Started Bar Code Symbologies Supported Laser Engine Options and Symbologies SupportedUsing Dolphin 7400/7450 for the First Time Unpack the Carton and Check Its ContentsCharging the Main Battery and Backup Battery Removing the Battery PackInstalling the Battery Pack Turning the Dolphin On And Off For the First TimeWaking the Dolphin From Sleep Mode Do not Press ANY Keys While the Terminal is Booting UPStylus Properties Screen Setting the Date/Time Using DetectoidPC and DetectoidCE Setting Up Communications with DetectoidInstalling DetectoidPC Page DetectoidCE Touchscreen-equipped terminals Configuring the ModemVerifying that Dolphin 7400/7450 is Working Properly Terminals without touchscreens Resetting the Dolphin Cold BootResetting the Dolphin Warm Boot Page System Features Dolphin 7400/7450 OverviewVGA Display Front Panel FeaturesLEDs Audio Signals ON/SCAN KeyCursor Keys KeyboardImage Engine Back Panel FeaturesDolphin Battery Well Battery Charging ContactsLaser Engine Hand StrapBumpers Communication Power Managing Battery PowerSetting Critical and Low Battery Points Using the Power Control PanelCriticalBatt=dworda LowBatt=dword19Charging the Battery Pack Servicing the Battery PackUsing the Battery Conditioning Utility Storing BatteriesUsing the Dolphin 7400/7450 Using the Image ReaderEntering Data Via the Touch ScreenLinear bar code 2D Matrix symbol Reading a Bar codeOmni-Directional Scanning Options Capturing ImagesCommunication Media Software Communication ProgramsUsing the Special Keys KeyboardsUsing the Cursor Keys To Use This Cursor Key Press DescriptionUsing the Modifier Keys Other Special KeysNavigating the Keyboard Key CombinationsUsing the Modem Dolphin 7400/7450 RF Terminal Configuring The Dolphin 7400/7450 RF Terminal Client Utilities for the Cisco Dsss 802.11b RadioConfiguring the Cisco Dsss Wlan Radio To Configure the Radio Card Host Connectivity Customizing the ActiveSync Remote IconPage Power Conditioning Dolphin Charging/Communication CradlesHub of the System Ir/IrDA Optical CommunicationsOrange LED HomeBase/IntelliBase/USB HomeBaseGreen LED Data is being sent from the Dolphin HomeBase AUX Battery LED Description Orange LED IntelliBase+Green LED Comm LED Description Red LEDBack Panel HomeBase/IntelliBaseIntelliBase+ USB HomeBase Bottom Panel of HomeBase/IntelliBase/IntelliBase+Powering the Dolphin Terminal Setting Up For Communications Charging Additional Battery Packs in the IntelliBase+Installing The Charging/Communication Cradle Deep-Cycling BatteriesIBM AT DB9 IBM XT Configuring the Dolphin Terminal for Communications Select StartSettingsControl PanelCommunications PropertiesPage Setting Up For Communications With The USB HomeBase Page Communicating with the Dolphin Terminal Wall Mounting Mounting the HomeBase/IntelliBase/USB HomeBaseDesk Mounting Page Top Panel Dolphin QuadChargerDolphin QuadCharger Parts and Function Setting Up The QuadCharger Supplying Power To The QuadChargerInserting and Removing Battery Packs Charging Batteries In The QuadChargerDescription Status LEDTroubleshooting Problem IssueDolphin Mobile Charging/Communication Cradles Mobile IntelliBase and Mobile Base Parts and Functions Front PanelDolphin Mobile IntelliBase/Mobile Base Mounting Bracket Power Supply RS-232 Connector Locking Lever RS-232 Bottom Panel of Mobile IntelliBase/Mobile Base Charging a Dolphin TerminalInstalling The Dolphin Mobile IntelliBase Mounting the Mobile IntelliBase Spring Arm AssemblyInstalling The Dolphin Mobile Base Setting the Baud Rate Configuring the Dolphin Terminal Select StartSettingsControl PanelCommunication SettingsDeveloping Applications Page How Problems Should Be Handled Warranty, Support and ServiceLimited Warranty Locations How To Extend Your WarrantyReturn Information Technical Assistance Assistance OnlineNorth America/Canada Europe, Middle East, and AfricaPage Press Appendix aWindows Keyboard Shortcuts Key Combination Function/Special Character Using the Modifier KeysKey Alpha/Numeric Keyboard Red key + T Red key + U Red key + W Red key + Y Key Numeric/Alpha Key Full Alpha Numeric Key/Key Combinations Function/Special Characters ALT + 3 +F12 Red key + P F16 Red key + Q F17 Hold the ALT key down as you type in the numbers HHP, Inc