Monarch 9800 Series manual R P e e l M o d e 9 8 3 0 o n l y

Page 20

F o r P e e l M o d e ( 9 8 3 0 o n l y )

In peel mode, the printer separates the backing paper from the label. The next label is not printed until the completed one is removed from the printer. Make sure the printer is configured for on-demand mode and the correct supply type.

The minimum feed length is 1.5 inches for peel mode. Hold the leading edge of peeled labels when printing on stock longer than six inches. You must use non-perforated supplies for peel mode. Follow the steps for loading supplies from the previous section. Then, follow these steps after you close the printhead.

1.Remove the labels from the first 10 inches of the backing paper.

2.Press down on the exit cover tabs to open the exit cover on the front of the printer.

Exit Cover

2-6Loading Supplies

Image 20

Contents Monarch Series Printers Canadian D.O.C. Warning Page Page TA B L E O F C O N T E N T S Page T T I N G S TA R T E D D i e n c e D e r i n g P r o g r a m m e r ’ s M a n u a l sO u t M o n a r c h Q u i c k s e t U t i l i t i e s P a c k i n g t h e P r i n t e rN n e c t i n g t h e P o w e r C a b l e T a b l i s h i n g C o m m u n i c a t i o n sN n e c t i n g t h e C o m m u n i c a t i o n C a b l e DTRT t i n g D I P S w i t c h e s 6Getting Started I n g t h e C o n t r o l P a n e l I n t e r S t a t u s L i g h t sT t o n F u n c t i o n s A t u s code B oA D I N G S U P P L I E S High EnergyA d i n g L a b e l s o r Ta g s Supply Holder Guides 4Loading Supplies Thumb Well R P e e l M o d e 9 8 3 0 o n l y Feed the backing paper over the peel bar I n g t h e O p t i o n a l Te a r B a r J u s t i n g t h e W i d e / N a r r o w K n o b s Page A D I N G R I B B O N A d i n g R i b b o n Printhead Tab Deflector Tab 4Loading Ribbon Take-up Core Take-up Reel I n g a H i g h E n e r g y R i b b o n G h E n e r g y R i b b o n L i m i t a t i o n s 8Loading Ribbon I N T I N G I n t i n g D e m a n d M o d e P r i n t i n gI n g B a t c h S e p a r a t o r s I n t i n g a n Error L a b e lE a r i n g B a t c h e s J u s t i n g P r i n t P o s i t i o n s I n t i n g t h e E u r o D o l l a r S y m b o l 6Printing R E a N D M a I N T E N a N C E E a r i n g L a b e l J a m s E a n i n gExit Cover Die Cut Sensor Supply Sensor Page P l a c i n g t h e P r i n t h e a d Page Do not touch here J u s t i n g t h e P r i n t C o n t r a s t P l a c i n g t h e F u s e Troubleshooting I n t i n g a Te s t L a b e l This section helps you correct some problems that may occur Tr o u b l e s h o o t i n gError M e s s a g e s T a Error sPage Page Page Page Page M m u n i c a t i o n F a i l u r e s T a F o r m a t t i n g Error s C h i n e Fault s Page Page Troubleshooting E C I F I C AT I O N S & a C C E S S O R I E S I n t e rO u t R i b b o n s B b o n SpecificationP p l i e s C e s s o r i e s 4Specifications & Accessories O S S a R Y FormatPage