Monarch 9800 Series manual

Page 61

703The printer sensed a calibration of different-sized black marks.

704Printer didn’t detect a sense mark within the maximum feed length or is out of supplies. Check or load supplies.

705Invalid batch received.

750Printhead is overheated, turn off the printer to let it cool.

751Printer didn’t detect a sense mark when expected.

752Printer detected a sense mark in the wrong place.

753Printer detected a sense mark that is too long.

754Out of ribbon or ribbon jam. Check or load ribbon. Remove any slack in the ribbon by turning the take-up reel clockwise.

755Printhead is open. Close the printhead.

756Out of supplies. Load supplies.

757Reload supplies (supply length mismatch).

758The supply was not seen or the on-demand sensor is not working correctly. Check for a supply jam. Clear the supply path or reload supplies. This error may occur if you remove a label too quickly in the on-demand mode. The printer does not recalibrate after this error.

759Knife is not moving. Call Technical Support.

760Knife jam. Remove any jammed tags from the knife. Call Technical Support.

761Stacker is full or jammed. Empty the stacker or clear the jam before continuing. The printer does not recalibrate after this error.

Troubleshooting 6-13

Image 61

Contents Monarch Series Printers Canadian D.O.C. Warning Page Page TA B L E O F C O N T E N T S Page T T I N G S TA R T E D D e r i n g P r o g r a m m e r ’ s M a n u a l s D i e n c eO u t M o n a r c h Q u i c k s e t U t i l i t i e s P a c k i n g t h e P r i n t e rT a b l i s h i n g C o m m u n i c a t i o n s N n e c t i n g t h e P o w e r C a b l eDTR N n e c t i n g t h e C o m m u n i c a t i o n C a b l eT t i n g D I P S w i t c h e s 6Getting Started I n t e r S t a t u s L i g h t s I n g t h e C o n t r o l P a n e lA t u s code B o T t o n F u n c t i o n sHigh Energy A D I N G S U P P L I E SA d i n g L a b e l s o r Ta g s Supply Holder Guides 4Loading Supplies Thumb Well R P e e l M o d e 9 8 3 0 o n l y Feed the backing paper over the peel bar I n g t h e O p t i o n a l Te a r B a r J u s t i n g t h e W i d e / N a r r o w K n o b s Page A D I N G R I B B O N A d i n g R i b b o n Printhead Tab Deflector Tab 4Loading Ribbon Take-up Core Take-up Reel I n g a H i g h E n e r g y R i b b o n G h E n e r g y R i b b o n L i m i t a t i o n s 8Loading Ribbon I N T I N G D e m a n d M o d e P r i n t i n g I n t i n gE a r i n g B a t c h e s I n t i n g a n Error L a b e lI n g B a t c h S e p a r a t o r s J u s t i n g P r i n t P o s i t i o n s I n t i n g t h e E u r o D o l l a r S y m b o l 6Printing R E a N D M a I N T E N a N C E E a n i n g E a r i n g L a b e l J a m sExit Cover Die Cut Sensor Supply Sensor Page P l a c i n g t h e P r i n t h e a d Page Do not touch here J u s t i n g t h e P r i n t C o n t r a s t P l a c i n g t h e F u s e Troubleshooting I n t i n g a Te s t L a b e l Tr o u b l e s h o o t i n g This section helps you correct some problems that may occurT a Error s Error M e s s a g e sPage Page Page Page Page M m u n i c a t i o n F a i l u r e s T a F o r m a t t i n g Error s C h i n e Fault s Page Page Troubleshooting I n t e r E C I F I C AT I O N S & a C C E S S O R I E SP p l i e s B b o n SpecificationO u t R i b b o n s C e s s o r i e s 4Specifications & Accessories Format O S S a R YPage