Monarch 9800 Series manual C h i n e Fault s

Page 60

574Batch data in check digit scheme doesn’t fit the format, or, the field contains blanks.

575The graphic included in your format could not be found.

600Imaging error because the batch was refused.

601An error occurred while the batch was imaging.

602The batch was not found during imaging.

611Font, bar code, or density in the batch doesn’t fit the format.

612Batch data is missing or doesn’t match the format.

613Reference point off tag.

614Portion of field off tag.

615Bar code width is greater than 16 inches, or keywords on PDF 417 bar code exceed 928.

616A bad dot falls on a bar code and the dot cannot be shifted. Call Customer Service to order a new printhead or printhead kit.

618 Magnification must be 1 to 7.

M a c h i n e F a u l t s

Errors 700 to 765 happen when there is a problem with the printer.

Error Description/Action

700An error is pending, and the printer cannot continue with the batch.

701Printer received a command that it cannot execute while it is running.

702Check your printer’s SETUP settings.

6-12Troubleshooting

Image 60

Contents Monarch Series Printers Canadian D.O.C. Warning Page Page TA B L E O F C O N T E N T S Page T T I N G S TA R T E D D i e n c e D e r i n g P r o g r a m m e r ’ s M a n u a l sO u t M o n a r c h Q u i c k s e t U t i l i t i e s P a c k i n g t h e P r i n t e rN n e c t i n g t h e P o w e r C a b l e T a b l i s h i n g C o m m u n i c a t i o n sN n e c t i n g t h e C o m m u n i c a t i o n C a b l e DTRT t i n g D I P S w i t c h e s 6Getting Started I n g t h e C o n t r o l P a n e l I n t e r S t a t u s L i g h t sT t o n F u n c t i o n s A t u s code B oA D I N G S U P P L I E S High EnergyA d i n g L a b e l s o r Ta g s Supply Holder Guides 4Loading Supplies Thumb Well R P e e l M o d e 9 8 3 0 o n l y Feed the backing paper over the peel bar I n g t h e O p t i o n a l Te a r B a r J u s t i n g t h e W i d e / N a r r o w K n o b s Page A D I N G R I B B O N A d i n g R i b b o n Printhead Tab Deflector Tab 4Loading Ribbon Take-up Core Take-up Reel I n g a H i g h E n e r g y R i b b o n G h E n e r g y R i b b o n L i m i t a t i o n s 8Loading Ribbon I N T I N G I n t i n g D e m a n d M o d e P r i n t i n gI n t i n g a n Error L a b e l E a r i n g B a t c h e sI n g B a t c h S e p a r a t o r s J u s t i n g P r i n t P o s i t i o n s I n t i n g t h e E u r o D o l l a r S y m b o l 6Printing R E a N D M a I N T E N a N C E E a r i n g L a b e l J a m s E a n i n gExit Cover Die Cut Sensor Supply Sensor Page P l a c i n g t h e P r i n t h e a d Page Do not touch here J u s t i n g t h e P r i n t C o n t r a s t P l a c i n g t h e F u s e Troubleshooting I n t i n g a Te s t L a b e l This section helps you correct some problems that may occur Tr o u b l e s h o o t i n gError M e s s a g e s T a Error sPage Page Page Page Page M m u n i c a t i o n F a i l u r e s T a F o r m a t t i n g Error s C h i n e Fault s Page Page Troubleshooting E C I F I C AT I O N S & a C C E S S O R I E S I n t e rB b o n Specification P p l i e sO u t R i b b o n s C e s s o r i e s 4Specifications & Accessories O S S a R Y FormatPage