Monarch 9800 Series manual Printhead Tab Deflector Tab

Page 27

3.Lift printhead assembly using the printhead tab until the assembly locks into place.

Printhead Tab

Deflector Tab

4.Push the deflector tab down.

5.Slide the extra ribbon core on the take-up reel as far as it will go with the "Monarch This End Out" writing facing out. Use your empty ribbon core as the take-up core. The take-up core only fits on the take-up reel one way. (An extra take-up core is available by ordering part number 117961.)

6.Remove the new ribbon from the package as shown. Do not wrinkle or crush the new ribbon.

Loading Ribbon 3-3

Image 27

Contents Monarch Series Printers Canadian D.O.C. Warning Page Page TA B L E O F C O N T E N T S Page T T I N G S TA R T E D P a c k i n g t h e P r i n t e r D i e n c eD e r i n g P r o g r a m m e r ’ s M a n u a l s O u t M o n a r c h Q u i c k s e t U t i l i t i e sT a b l i s h i n g C o m m u n i c a t i o n s N n e c t i n g t h e P o w e r C a b l eDTR N n e c t i n g t h e C o m m u n i c a t i o n C a b l eT t i n g D I P S w i t c h e s 6Getting Started I n t e r S t a t u s L i g h t s I n g t h e C o n t r o l P a n e lA t u s code B o T t o n F u n c t i o n sHigh Energy A D I N G S U P P L I E SA d i n g L a b e l s o r Ta g s Supply Holder Guides 4Loading Supplies Thumb Well R P e e l M o d e 9 8 3 0 o n l y Feed the backing paper over the peel bar I n g t h e O p t i o n a l Te a r B a r J u s t i n g t h e W i d e / N a r r o w K n o b s Page A D I N G R I B B O N A d i n g R i b b o n Printhead Tab Deflector Tab 4Loading Ribbon Take-up Core Take-up Reel I n g a H i g h E n e r g y R i b b o n G h E n e r g y R i b b o n L i m i t a t i o n s 8Loading Ribbon I N T I N G D e m a n d M o d e P r i n t i n g I n t i n gI n t i n g a n Error L a b e l E a r i n g B a t c h e sI n g B a t c h S e p a r a t o r s J u s t i n g P r i n t P o s i t i o n s I n t i n g t h e E u r o D o l l a r S y m b o l 6Printing R E a N D M a I N T E N a N C E E a n i n g E a r i n g L a b e l J a m sExit Cover Die Cut Sensor Supply Sensor Page P l a c i n g t h e P r i n t h e a d Page Do not touch here J u s t i n g t h e P r i n t C o n t r a s t P l a c i n g t h e F u s e Troubleshooting I n t i n g a Te s t L a b e l Tr o u b l e s h o o t i n g This section helps you correct some problems that may occurT a Error s Error M e s s a g e sPage Page Page Page Page M m u n i c a t i o n F a i l u r e s T a F o r m a t t i n g Error s C h i n e Fault s Page Page Troubleshooting I n t e r E C I F I C AT I O N S & a C C E S S O R I E SB b o n Specification P p l i e sO u t R i b b o n s C e s s o r i e s 4Specifications & Accessories Format O S S a R YPage