Marshall electronic V-R261-DLW operating instructions Ancillary Submenu

Page 29

Colorize Waveform

Use the Colorize Waveform option to add or remove color from the Waveform display. When Colorize Waveform is ON, the YUV and RGB data components on the Waveform display will appear in different colors. When Colorize Waveform is OFF, all YUV and RGB data components will appear as white on the Waveform display.

Limits

Use the Limits option to differentiate data (indicated by a red highlight) on the Waveform display that goes above a Limit Max (maximum) and goes below a Limit Min (minimum) set in the Wave/Vector submenu. The Limit maximum and minimum can be set from 0000 to 1023. Note: Setting the Limits option to ON will override the Colorize Waveform option. All Waveform display data within the limits will appear in white.

Limit Max

Use this to set the desired maximum for the Limit display of the waveform monitor. Any Waveform data that goes beyond this Limit Max will be displayed in red.

Limit Min

Use this to set the desired minimum for the Limit display of the waveform monitor. Any Waveform data that goes below this Limit Max will be displayed in red.

Vectorscope Targets

Use the Vectorscope Targets option to set your Vectorscope targets up for 75% or 100% color bar signals. You can also set your Vectorscope Targets to the OFF position.

Overlay Position

Use the Overlay Position option to place the Waveform, Vectorscope and Audio Level display on the Top or Bottom of the screen while in the DLW Overlay display mode. You can also set your Overlay display to OFF.

Overlay Transparency

Use the Overlay Transparency option to set the transparency of the Waveform, Vectorscope and Audio Level display while in DLW Overlay mode. Choose a value from 000-100. A low value will cause the Waveform, Vectorscope and Audio Level data to blend into the background, while a high value will make the data appear more visible against the video display in the background.

Ancillary Submenu

Use the Ancillary submenu to determine which ancillary packet IDs should be counted in the Ancillary Status portion of the DLW monitor display.

29

Image 29
Contents Model No. V-R261-DLW Operating InstructionsThis page intentionally left blank Contents Multi mode, Vectorscope and Waveform Monitor mode FeaturesInstallation Installation and Initial SetupConnections, Power-On and Initial Setup UnpackingPower Button Front Panel FeaturesRS-422/485 Serial Interface Rear Panel FeaturesFollowing SDI standards are supported by the V-R261-DLW Compatible Input FormatsDLW Monitor Layouts Waveform Monitor Mode Full Screen Video Mode On-Screen Menu On-Screen Menu Marker Setup SubmenuMarkers Center Marker Marker BackgroundBlue-Only Mode Video Config SubmenuMonochrome Mode Aspect Ratio Settings Pixel-to-Pixel ModeDVI-A CSC Mode DVI-Analog input only Analog Phase DVI-Analog or VGA input onlyDVI-D CSC Mode DVI-D input only Curtain ColorHdmi CSC Auto Hdmi input only, via the DVI-I interface Color Config SubmenuSystem Config Submenu User-Definable Function Buttons Saving and Loading User PresetsStatus Display OSD Config SubmenuIMD State LED Tally OSD TallyAnc. Timecode OSD TimeoutAudio Monitor CC Monitor Closed CaptioningOverview IMD Config SubmenuIMD ID # IMD Group #TSL Tally SourceIMD Tally Mode IMD Fixed Config SubmenuIMD Baud Rate IMD Name S/NClosed Captioning Submenu ServiceIMD Fixed Align IMD Fixed StringColor Waveform ModeWave/Vector Submenu Waveform Scale Ancillary Submenu DID/SDID Software Version Display Service SubmenuPanel RS-422/485 Serial Interface RJ12 SpecificationsDimensions Warranty MaintenanceScreen Cleaning Burn-In WarningThis page intentionally left blank Marshall Electronics, Inc