Ultra electronic M9006-644E, M9007-224E Cleaning Kits for Europe, Middle East, Africa & Asia

Page 11

www.ultramagicard.com

AVALON and AVALON DUO Printer USER MANUAL

Cleaning Supplies

Three cleaning cards are bundled with each new Avalon printer. You can purchase additional cleaning kits, which include cleaning cards, rollers and pens.

Cleaning Kits for Europe, Middle East, Africa & Asia

•Part # M9005-761 - 10 cleaning cards, 5 rollers and a cleaning pen.

Cleaning Kits for North and South America

•Part # N9005-761 Medium - 10 cleaning cards, 3 rollers, and 2 cleaning pens.

•Part # N9005-761 Large - 20 cleaning cards, 6 rollers, and 3 cleaning pens.

Step 1. Every 250 Prints or Sooner –

Using a cleaning card

We recommend that you clean your printer using a cleaning card after every 250 prints or each time you replace the dye-film. You should do this more often if you print only a few cards a day.

To clean the card feed mechanism:

•The printer must be switched ON.

•Remove the card hopper and open the top door (the red light comes on).

•Ensure the dye film is not touching the base of the printer inside. If it is, take up the slack by winding the supply spool backwards or remove the dye film before starting the cleaning cycle.

• Take a fresh cleaning card from its packaging.	1

•Insert the narrow end into the card feed slot (picture 1).

•Press the black button on the back of the printer (located above the USB connector). The card is drawn into the printer (picture 2) and then ejected. Repeat this several times with both sides of the same card.

•To ensure that the rear feed rollers located under the card hopper are thoroughly cleaned, set the printer to its cleaning cycle, and instead of inserting the card, simply hold it against these rollers (picture 3).

2

3

Page 11 of 31

Image 11

Contents Standard Option Avalon Duo Only Index About this guide Safety InstructionsBefore Use Consumables Install the dye filmPrepare the cleaning cassette UnpackingPrint a test card Click ‘Next ’ on the ‘Available Platforms’ screen Installing the UltraDriverLoading the Dye-Film Ribbon Choosing the right Dye-Film Ribbon Choosing the right Cards Loading Infra-Red Barcode Cards Loading the CardsLoading Magnetic Stripe Cards Loading HoloPatch CardsTo clean your printer, follow the three main steps below Cleaning your PrinterTo clean the card feed mechanism Cleaning Kits for Europe, Middle East, Africa & AsiaCleaning Kits for North and South America Using a cleaning cardTo clean the printhead Changing the cleaning rollerTo replace the cleaning roller Printer Tab Printer Driver settingsTo access the Printer Driver Settings Magnetic Encoding Verify Printing Options Number of CopiesHand Feed Magnetic Encoding Encode OnlyCard Front & Card Back Tabs Rotate Security Print OvercoatHoloKote Card Orientation Landscape/PortraitAll Black in image is printed with Black Resin Options Halftoning Monochrome OnlyOvercoat Holes Overcoat OptionsOvercoat Area Selection Printhead & Image Positions Colour AdjustmentPrinthead Power Advanced TabImage Position Yellow, Magenta, Cyan YMCBlack Resin OvercoatRestore Defaults Restore Factory Defaults Save & Restore TabSave & Restore Settings Restore Settings from File Save Settings to FileThen select Add or Remove Programs Uninstalling the UltraDriverTo delete the UltraDriver Magicard Support Utility Install the Magicard Support Utility from the Driver CDEthernet Upgrade FirmwareQuery Printer Problem Probable Cause Dye Film ProblemsDriver Related Problems Card Feed ProblemsMagnetic Encoding Problems Limited Warranty Information WarrantyCall EU +44 0 1305 762 Technical Support, Service, and Warranty EnquiriesSales for Europe Sales and Service Center for North and South AmericaContact Us Sales Sales for Latin AmericaSales and Service for Singapore & Malaysia Sales and Service for RussiaEU Declaration of Conformity EMCFederal Communications Commission FCC Statement Canadian Department of Communications Statement