Pro-Tech ULV Celeron M 3.5" Embedded Card With VGA/ SOUND/ LAN, EB-471LF M1 user manual Hardware

Page 11

	HARDWARE	CHAPTER
	HARDWARE	2
	CONFIGURATION	2
	CONFIGURATION

QUICK START

Helpful information describes the jumper & connector settings, and component locations.

Section includes:

zJumper & Connector Quick Reference Table

zComponent Locations

zConfiguration and Jumper settings

zConnector’s Pin Assignments

Page 2-1

Image 11

Contents USER’S Manual EB-471LF Celeron M FCC Notice Table of Contents Appendix Expansion BUS Introduction About this Manual Hardware ConfigurationCPU System SpecificationDisplay Safety Precautions Hardware Jumper & Connector Quick Reference Table Component Locations EB-471LF Connector, Jumper and Component locationsJumpers and Caps HOW to SET the JumpersJumper Settings Jumper DiagramsRS-232 RS-422 RS-485 COM Port ConnectorRS232/422/485 COM2 Selection Jumper Settings Function Pin closed IllustrationsJPANEL1 7,8 Reset Connector KEYBOARD/MOUSE ConnectorReset Connector Hard Disk Drive LED ConnectorIrda Connector External Speaker ConnectorPower LED Connector VGA Connector System FAN ConnectorPIN Assignment Hard Disk Drive ConnectorLAN Connector Universal Serial BUS ConnectorClear Cmos Data Selection Function Jumper SettingSettings Power Requirement SelectionInverter Connector AT Power ConnectorIllustration RESET/NMI Watchdog SelectionLvds Connector Panel Voltage Selection TV-OUT Connector Sound ConnectorLAN LED Software Utilities Filename Purpose Assume that CD ROM drive is D IntroductionVGA Driver Utility Installation of VGA Driver To update VGA Bios for LCD Flat Panel Display Flash Bios UpdateSystem Bios Update Page3-5 Introduction LAN Driver UtilitySound Driver Utility Installation Procedure for Windows 9x/NT/2000/XPInstallation of Utility for Windows 98SE/ME/2000/XP Intel Chipset Software Installation UtilityInstallation of Utility for Windows 98SE/ 2000/XP USB2.0 Software Installation UtilityConfiguration Sequence Watchdog Timer ConfigurationPage3-11 Award Bios Setup Introduction Setup program initial screen Entering SetupCmos Setup screen Standard Cmos FeaturesIDE Primary Master / Slave IDE Secondary Master / Slave Base Memory Drive a and Drive BVideo Halt onAward Hard Disk Type Table Hard Disk AttributesCPU L1 & L2 Cache Advanced Bios FeaturesBios Features Setup Screen Quick Power on SELF-TESTTypematic Delay Msec FIRST/SECOND/ Boot DeviceBoot UP Numlock Status Typematic Rate SettingChipset Features Setup Screen Advanced Chipset FeaturesSystem Bios Cacheable Active to Precharge DelayDram RAS# to CAS# Delay Dram Data Integrity ModeON-CHIP VGA Delayed TransactionMemory Hole AT 15M-16M AGP Aperture SizeIntegrated Peripherals Integrated Peripherals Setup ScreenPrimary Master/Slave Udma Secondary Master/Slave Udma Onchip IDE DeviceOnChip Primary PCI IDE Primary Master/Slave PIO Secondary Master/Slave PIOUSB Mouse Support Onboard DeviceUSB Controller USB Keyboard SupportSuper IO Device Modem USE IRQ Power Management SetupPower Management Setup Screen Power ManagementReset Configuration Data PNP/PCI ConfigurationPNP/PCI Configuration Setup Screen IRQ-n Assigned to Resource Controlled byIRQ Resources Current System FAN Speed Current Warning TemperatureCurrent CPU Temperature PC Health StatusSpread Spectrum Frequency Control Setup ScreenFrequency Control Auto Detect PCI CLKLoad Optimized Defaults Load FAIL-SAFE DefaultsTo Disable the Password SET Supervisor PASSWORD/SET User PasswordTo SET a Password Save & Exit Setup Exit Without Saving Expansion BUS PC/104 Plus BUS Connector PIN Assignment Technical Summary Block Diagram IRQ Assignment Interrupt MAPCode Assignment RTC & Cmos RAM MAPDMA Channel Map Assignment Timer & DMA Channels MAPTimer Channel Map Assignment Map Memory MAPMemory Map