Pro-Tech EB-471LF M1 user manual Power Management Setup Screen, Modem USE IRQ, PM Events

Page 58

Chapter 4 Award BIOS Setup

4-7. POWER MANAGEMENT SETUP

ChoosePOWER MANAGEMENT SETUPoption on the main menu, a display will be shown on screen as below :

Phoenix - AwardBIOS CMOS Setup Utility

Power Management Setup

Power Management

 

[User Define]

Item Help

MODEM Use IRQ

 

[3]

 

 

** Reload Global Timer Events **

 

Menu Level ►

[Disabled]

 

Primary IDE 0

 

 

Primary IDE 1

 

[Disabled]

 

Secondary IDE 0

 

[Disabled]

 

Secondary IDE 1

 

[Disabled]

 

FDD, COM, LPT Port

 

[Disabled]

 

 

 

 

↑↓→←: Move Enter: Select

+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values

F6: Fail-Safe Defaults F7:Optimized Defaults

 

 

 

 

Power Management Setup Screen

The “Power Management Setup” allows the user to configure the system to the most effectively save energy while operating in a manner consistent with your own style of computer use.

POWER MANAGEMENT:

This item allows you to select the Power Management mode.

MODEM USE IRQ:

This item enable you to name the interrupt request (IRQ) line assigned to the modem (if any) on your system. Activity of the selected IRQ always awakens the system.

PM EVENTS:

PM events are I/O events whose occurrence can prevent the system from entering a power saving mode or can awaken the system from such a mode. In effect, the system remains alert for anything, which occurs to a device which is configured as Enabled, even when the system is in a power down mode. (1) Primary IDE 0 (2) Primary IDE 1 (3) Secondary IDE 0 (4) Secondary IDE 1 (5) FDD, COM, LPT Port

EB-471LF USERS MANUAL

Page: 4-17

Image 58
Contents USER’S Manual EB-471LF Celeron M FCC Notice Table of Contents Appendix Expansion BUS Introduction Hardware Configuration About this ManualSystem Specification CPUDisplay Safety Precautions Hardware Jumper & Connector Quick Reference Table EB-471LF Connector, Jumper and Component locations Component LocationsHOW to SET the Jumpers Jumpers and CapsJumper Diagrams Jumper SettingsCOM Port Connector RS-232 RS-422 RS-485Jumper Settings Function Pin closed Illustrations RS232/422/485 COM2 SelectionHard Disk Drive LED Connector KEYBOARD/MOUSE ConnectorReset Connector JPANEL1 7,8 Reset ConnectorPower LED Connector External Speaker ConnectorIrda Connector System FAN Connector VGA ConnectorHard Disk Drive Connector PIN AssignmentUniversal Serial BUS Connector LAN ConnectorFunction Jumper Setting Clear Cmos Data SelectionPower Requirement Selection SettingsAT Power Connector Inverter ConnectorRESET/NMI Watchdog Selection IllustrationLvds Connector Panel Voltage Selection Sound Connector TV-OUT ConnectorLAN LED Software Utilities VGA Driver Utility IntroductionFilename Purpose Assume that CD ROM drive is D Installation of VGA Driver System Bios Update Flash Bios UpdateTo update VGA Bios for LCD Flat Panel Display Page3-5 LAN Driver Utility IntroductionInstallation Procedure for Windows 9x/NT/2000/XP Sound Driver UtilityIntel Chipset Software Installation Utility Installation of Utility for Windows 98SE/ME/2000/XPUSB2.0 Software Installation Utility Installation of Utility for Windows 98SE/ 2000/XPWatchdog Timer Configuration Configuration SequencePage3-11 Award Bios Setup Introduction Entering Setup Setup program initial screenStandard Cmos Features Cmos Setup screenIDE Primary Master / Slave IDE Secondary Master / Slave Halt on Drive a and Drive BVideo Base MemoryHard Disk Attributes Award Hard Disk Type TableQuick Power on SELF-TEST Advanced Bios FeaturesBios Features Setup Screen CPU L1 & L2 CacheTypematic Rate Setting FIRST/SECOND/ Boot DeviceBoot UP Numlock Status Typematic Delay MsecAdvanced Chipset Features Chipset Features Setup ScreenDram Data Integrity Mode Active to Precharge DelayDram RAS# to CAS# Delay System Bios CacheableAGP Aperture Size Delayed TransactionMemory Hole AT 15M-16M ON-CHIP VGAIntegrated Peripherals Setup Screen Integrated PeripheralsPrimary Master/Slave PIO Secondary Master/Slave PIO Onchip IDE DeviceOnChip Primary PCI IDE Primary Master/Slave Udma Secondary Master/Slave UdmaUSB Keyboard Support Onboard DeviceUSB Controller USB Mouse SupportSuper IO Device Power Management Power Management SetupPower Management Setup Screen Modem USE IRQPNP/PCI Configuration Setup Screen PNP/PCI ConfigurationReset Configuration Data IRQ Resources Resource Controlled byIRQ-n Assigned to PC Health Status Current Warning TemperatureCurrent CPU Temperature Current System FAN SpeedAuto Detect PCI CLK Frequency Control Setup ScreenFrequency Control Spread SpectrumLoad FAIL-SAFE Defaults Load Optimized DefaultsTo SET a Password SET Supervisor PASSWORD/SET User PasswordTo Disable the Password Save & Exit Setup Exit Without Saving Expansion BUS PC/104 Plus BUS Connector PIN Assignment Technical Summary Block Diagram Interrupt MAP IRQ AssignmentRTC & Cmos RAM MAP Code AssignmentTimer Channel Map Assignment Timer & DMA Channels MAPDMA Channel Map Assignment Memory Map Memory MAPMap