Pro-Tech ULV Celeron M 3.5" Embedded Card With VGA/ SOUND/ LAN user manual Memory Hole AT 15M-16M

Page 53

Chapter 4 Award BIOS Setup

MEMORY HOLE AT 15M-16M:

You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user information of peripherals that need to use this area of system memory usually discusses their memory requirements.

DELAYED TRANSACTION:

The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1.

AGP APERTURE SIZE:

This field determines the effective size of the Graphic Aperture used for a particular GMCH configuration. It can be updated by the GMCH-specific BIOS configuration sequence before the PCI standard bus enumeration sequence takes place. If it is not updated then a default value will select an aperture of maximum size.

ON-CHIP VGA :

By default, the On-Chip VGA or chipset-integrated VGA is “Enabled”.

ON-CHIP FRAME BUFFER SIZE: (depend on chipset)

The On-Chip Frame Buffer Size can be set as 1MB or 8MB. This memory is shared with the system memory.

BOOT DISPLAY: (depend on chipset)

Boot Display determines the display output device where the system boots. The options are CRT and LVDS.

PANEL TYPE: (depend on chipset)

This field allows user to decide the LVDS panel resolution. The available choices are: 640x480 18bits, 800x600 18bits, 1024x768 18bits, 1280x1024 36bits, 1400x1050 36bits, 1600x1200 36bits, and 1024x768 24bits.

Page: 4-12

EB-471LF USERS MANUAL

Image 53
Contents USER’S Manual EB-471LF Celeron M FCC Notice Table of Contents Appendix Expansion BUS Introduction About this Manual Hardware ConfigurationCPU System SpecificationDisplay Safety Precautions Hardware Jumper & Connector Quick Reference Table Component Locations EB-471LF Connector, Jumper and Component locationsJumpers and Caps HOW to SET the JumpersJumper Settings Jumper DiagramsRS-232 RS-422 RS-485 COM Port ConnectorRS232/422/485 COM2 Selection Jumper Settings Function Pin closed IllustrationsReset Connector KEYBOARD/MOUSE ConnectorHard Disk Drive LED Connector JPANEL1 7,8 Reset ConnectorIrda Connector External Speaker ConnectorPower LED Connector VGA Connector System FAN ConnectorPIN Assignment Hard Disk Drive ConnectorLAN Connector Universal Serial BUS ConnectorClear Cmos Data Selection Function Jumper SettingSettings Power Requirement SelectionInverter Connector AT Power ConnectorIllustration RESET/NMI Watchdog SelectionLvds Connector Panel Voltage Selection TV-OUT Connector Sound ConnectorLAN LED Software Utilities Filename Purpose Assume that CD ROM drive is D IntroductionVGA Driver Utility Installation of VGA Driver To update VGA Bios for LCD Flat Panel Display Flash Bios UpdateSystem Bios Update Page3-5 Introduction LAN Driver UtilitySound Driver Utility Installation Procedure for Windows 9x/NT/2000/XPInstallation of Utility for Windows 98SE/ME/2000/XP Intel Chipset Software Installation UtilityInstallation of Utility for Windows 98SE/ 2000/XP USB2.0 Software Installation UtilityConfiguration Sequence Watchdog Timer ConfigurationPage3-11 Award Bios Setup Introduction Setup program initial screen Entering SetupCmos Setup screen Standard Cmos FeaturesIDE Primary Master / Slave IDE Secondary Master / Slave Video Drive a and Drive BHalt on Base MemoryAward Hard Disk Type Table Hard Disk AttributesBios Features Setup Screen Advanced Bios FeaturesQuick Power on SELF-TEST CPU L1 & L2 CacheBoot UP Numlock Status FIRST/SECOND/ Boot DeviceTypematic Rate Setting Typematic Delay MsecChipset Features Setup Screen Advanced Chipset FeaturesDram RAS# to CAS# Delay Active to Precharge DelayDram Data Integrity Mode System Bios CacheableMemory Hole AT 15M-16M Delayed TransactionAGP Aperture Size ON-CHIP VGAIntegrated Peripherals Integrated Peripherals Setup ScreenOnChip Primary PCI IDE Onchip IDE DevicePrimary Master/Slave PIO Secondary Master/Slave PIO Primary Master/Slave Udma Secondary Master/Slave UdmaUSB Controller Onboard DeviceUSB Keyboard Support USB Mouse SupportSuper IO Device Power Management Setup Screen Power Management SetupPower Management Modem USE IRQReset Configuration Data PNP/PCI ConfigurationPNP/PCI Configuration Setup Screen IRQ-n Assigned to Resource Controlled byIRQ Resources Current CPU Temperature Current Warning TemperaturePC Health Status Current System FAN SpeedFrequency Control Frequency Control Setup ScreenAuto Detect PCI CLK Spread SpectrumLoad Optimized Defaults Load FAIL-SAFE DefaultsTo Disable the Password SET Supervisor PASSWORD/SET User PasswordTo SET a Password Save & Exit Setup Exit Without Saving Expansion BUS PC/104 Plus BUS Connector PIN Assignment Technical Summary Block Diagram IRQ Assignment Interrupt MAPCode Assignment RTC & Cmos RAM MAPDMA Channel Map Assignment Timer & DMA Channels MAPTimer Channel Map Assignment Map Memory MAPMemory Map