Ultratec INTELE-MODEM manual Hang up, Product code, Speaker on/off The default is M1, Online

Page 22

on page 21 for more information.

F1–Full-duplex. In full-duplex, your modem sends the characters you type only to the other computer or TTY. You read the characters on your screen when the other computer or TTY sends them back. If typed characters do not appear on your monitor, change your setting to half-duplex.

H–Hang up

If you want to hang up at any time during or after a call, use the ATH Command.

I–Product code

The ATI Command displays a software revision code.

M–Speaker on/off (The default is M1)

M0–The speaker is always off.

M1–The speaker is on until an ASCII carrier or a Baudot character is detected.

M2–The speaker is always on.

N–Sensitivity (The default is N1)

Sensitivity controls how the Intele–Modem listens to sounds on the telephone line. If your modem is having trouble receiving data correctly, set it to high sensitivity. This is an Ultratec addition to the standard command set.

N0–High sensitivity N1–Normal sensitivity

O–Online

Use this command to return to on-line mode when you’re in command mode.

Q–Quiet (The default is Q0)

The Quiet command determines whether or not the modem sends its response messages to the computer monitor.

Q0–The modem sends response messages to your computer monitor.

Q1–Response messages are not sent to your computer monitor.

Sn?–Value of any S register

Use this command to find out the value of any of the S registers. For example, the command ATS1? asks the modem for the number of times the phone has rung.

S0–number of rings (The default is S0=0)

When the modem is in answer mode, the S0 register tells it how many rings to listen for before automatically answering the phone. You can set it for any number from 0 to 255.

S0=0 is the manual answer mode (default setting). Your Intele–Modem will not automatically answer the telephone when S0 is set to 0. If your modem is turned on and a call comes in, it will send the response RING to your computer monitor. You must use the command ATA to answer the call. After you answer, you will read CONNECT or CONNECT TTY when communication is established. If your modem does not establish a connection, press Escape to hang up and return to command mode.

S0=1 tells the modem to Auto-Answer after one (1) ring.

S0=n means Auto-Answer after n rings.

Setting S0 to any number greater than 0 has the effect of putting it into Auto- Answer mode. To take the modem out of Auto-Answer mode, set S0 back to 0.

S1–Ring count

This register is increased each time the phone rings.

S2–Set escape character (The default is S2=43, the ASCII number for the + character)

The escape character is part of the escape sequence, which puts the modem in command mode. This is the escape sequence: Wait until data transmission has stopped for at least one second, type the escape character three times, then wait another second. Your Intele–Modem will respond with OK, and you can enter a command. Use the ATO Command to go back on- line.

18 • COMPLETE HAYES COMMANDS

Image 22
Contents HOW to USE Your INTELE-MODEM Ultratec, Inc Science Drive Madison, WI Contents II Contents Introduction How to answer a call Where to find moreHow to make a call Information Quick GuideSetting up HOW to SET UP Your INTELE-MODEMEquipment you need HOW to USE Your INTELE-MODEM General procedure Calling with INTELE-MENU CommandsStep-by-step instructions Dialing a number lights the Off-Hook and Signal indicators Special situationsAnswering with Intele-Menu commands Changing communication settingsSetting UP AUTO-ANSWER INTELE-MENU Command SET How to use the commandsWhat each command does Telephone FunctionsCommunication Settings Message Functions Auto-Answer Functions Calling with Hayes Commands How to call another computer or a TTYHow to change communication settings How to answer a call from a computer or TTYSetting up Auto-Answer Default settings Complete Hayes CommandsHow to type commands Primary CommandsWhat each command means and how to use it Quiet The default is Q0 Speaker on/off The default is M1Sensitivity The default is N1 S0-number of rings The default is S0=0S5-Define backspace character The default is S5=8 S3-Define carriage return character The default is S3=13S4-Define line feed character The default is S4=10 S6-Set wait time before dialing The default is S6=2Response message list The default is S15-Auto-answer abort enable The default isCommand to reset your Intele-Modem Problems and Solutions How do I download a file?Appendix a Specifications and Service Service information Appendix B Modem Terminology Appendix C INTELE-MENU Help Menu ======= AUTO-ANSWER Functions =======Appendix D Ascii Character Table Dec Hex Char Keybd ActerFCC Information