Telit Wireless Solutions UC864 manual USB Port, Communication ports combinations

Page 37

UC864-E Hardware User Guide

1vv0300766a Rev.1 - 31/01/08

9 USB Port

UC864-E includes an integrated universal serial bus (USB) transceiver, compliant with USB 2.0 specification, for interfacing UC864-E to a computer as a USB peripheral or connecting the UC864-E to other peripherals. It supports the USB low-speed (1.5 Mbits/s) and full-speed (12 Mb/s) modes. In HSDPA (High Speed download Packet Access) mode, the downlink data speed rates up to 7.2Mbps. Hence you need to interface UC864-E to your applications in full-speed (12Mbits/s) mode.

You can use USB for the following purposes: communication with external peripheral devices, debug monitor

USB

Signal

UC864-E

Usage

Pin No.

 

Pad No.

 

 

 

 

 

1

USB_VBUS

48

Power supply for the internal USB transceiver. This pin is

 

 

 

configured as an analog input or an analog output depending

 

 

 

upon the type of peripheral device connected.

 

 

 

 

2

USB_D-

80

Minus (-) line of the differential, bi-directional USB signal to/from

 

 

 

the peripheral device

 

 

 

 

3

USB D+

79

Plus (+) line of the differential, bi-directional USB signal to/from

 

 

 

the peripheral device

 

 

 

 

4

USB_ID

35

Analog input used to sense whether a peripheral device is

 

 

 

connected, and determine the peripheral type, a host or a slave

 

 

 

 

NOTE: the UC864-E is turned fully on also by connecting the module’s USB port as slave (considering also the presence of VBATT supply).

9.1Communication ports combinations

The following port combinations are available on the UC864-E module:

UART (AT command) +USB (DATA/TRACE)

USB (AT command) + USB (DATA/TRACE)

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved

page 37 of 51

Image 37
Contents UC864 Hardware User Guide This document is relating to the following products UC864-E Hardware User GuideContents 10.4 10.311.1 11.2Disclaimer Overview Length 36.2 mm Width 30 mm Thickness 8mm Mechanical DimensionsPIN-OUT UC864-E module connectionsCmos Reserved Pin Signal Function 1 UC864-E Antenna connectorTurning on the UC864-E Hardware Commands10k Hardware shutdown Turning OFF the UC864-EHardware Unconditional Restart 10k +1.8 Power Supply Requirements Power SupplyUC864-E Hardware User Guide Electrical Design Guidelines General Design Rules1.2 + 12V input Source Power Supply Design Guidelines UC864-E Hardware User Guide Battery Source Power Supply Design Guidelines UC864-E Hardware User Guide Thermal Design Guidelines Power Supply PCB layout Guidelines Antenna Requirements AntennaAntenna Installation Guidelines Absolute Maximum Ratings -Not Functional Logic level specificationsOperating Range Interface levels Operating Range Interface levels 1.8V CmosReset signal Absolute Maximum Ratings Not Functional Serial PortsSignals of the UC864-E serial port are RS232 level translation UC864-E Hardware User Guide UC864-E Hardware User Guide 5V Uart level translation UC864-E Hardware User Guide Communication ports combinations USB PortGenerality Audio Section OverviewDefinitions SelectionInput lines microphone Electrical CharacteristicsEarMT Buffers Output lines speakerNot General Purpose I/OLogic level specifications Using a Gpio Pad as Output Using a Gpio Pad as InputUsing the Alarm Output GPIO6 Using the Buzzer Output GPIO7 LED status Device Status Indication of network service availabilityOperating Range VAUX1 power supply VAUX1 power outputRTC Bypass out Mounting UC864-E on your board USB Vbus Usbid Debug of the UC864-E in productionConformity Assessment Issues Safety Recommandations Revision Date Changes Document Change Log