Telit Wireless Solutions UC864 manual Conformity Assessment Issues

Page 49

UC864-E Hardware User Guide

1vv0300766a Rev.1 - 31/01/08

12 Conformity Assessment Issues

The UC864-E module is assessed to be conforming to the R&TTE Directive as stand-alone products, so if the module is installed in conformance with Dai Telecom installation instructions require no further evaluation under Article 3.2 of the R&TTE Directive and do not require further involvement of a R&TTE Directive Notified Body for the final product.

In all other cases, or if the manufacturer of the final product is in doubt then the equipment integrating the radio module must be assessed against Article 3.2 of the R&TTE Directive.

In all cases assessment of the final product must be made against the Essential requirements of the R&TTE Directive Articles 3.1(a) and (b), safety and EMC respectively, and any relevant Article 3.3 requirements.

The UC864-E module is conforming to the following European Union Directives:

•R&TTE Directive 1999/5/EC (Radio Equipment & Telecommunications Terminal Equipments)

•Low Voltage Directive 73/23/EEC and product safety

•Directive 89/336/EEC for conformity for EMC

In order to satisfy the essential requisite of the R&TTE 99/5/EC directive, the UC864-E module is compliant with the following standards:

•Radio Spectrum, Standard: EN 301 511 and 3GPP 51.010-1

•EMC (Electromagnetic Compatibility). Standards: EN 301 489-1 and EN 301 489-7

•LVD (Low Voltage Directive) Standards: EN 60 950

In this document and the Hardware User Guide, Software User Guide all the information you may need for developing a product meeting the R&TTE Directive is included.

The UC864-E module is conforming to the following US Directives:

•Use of RF Spectrum. Standards: FCC 47 Part 24 (GSM 1900)

•EMC (Electromagnetic Compatibility). Standards: FCC47 Part 15

To meet the FCC's RF exposure rules and regulations:

-The system antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all the persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

-The system antenna(s) used for this module must not exceed 3 dBi for mobile and fixed or mobile operating configurations.

-Users and installers must be provided with antenna installation instructions and transmitter

operating conditions for satisfying RF exposure compliance.

Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and to have their complete product tested and approved for FCC compliance.

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved

page 49 of 51

Page 48 Page 50
Image 49
Page 48 Page 50
Contents UC864 Hardware User Guide This document is relating to the following products UC864-E Hardware User GuideContents 10.4 10.311.1 11.2Disclaimer Overview Length 36.2 mm Width 30 mm Thickness 8mm Mechanical DimensionsPIN-OUT UC864-E module connectionsCmos Reserved Pin Signal Function 1 UC864-E Antenna connectorTurning on the UC864-E Hardware Commands10k Hardware shutdown Turning OFF the UC864-EHardware Unconditional Restart 10k +1.8 Power Supply Requirements Power SupplyUC864-E Hardware User Guide Electrical Design Guidelines General Design Rules1.2 + 12V input Source Power Supply Design Guidelines UC864-E Hardware User Guide Battery Source Power Supply Design Guidelines UC864-E Hardware User Guide Thermal Design Guidelines Power Supply PCB layout Guidelines Antenna Requirements AntennaAntenna Installation Guidelines Absolute Maximum Ratings -Not Functional Logic level specificationsOperating Range Interface levels Operating Range Interface levels 1.8V CmosReset signal Absolute Maximum Ratings Not Functional Serial PortsSignals of the UC864-E serial port are RS232 level translation UC864-E Hardware User Guide UC864-E Hardware User Guide 5V Uart level translation UC864-E Hardware User Guide Communication ports combinations USB PortGenerality Audio Section OverviewDefinitions SelectionInput lines microphone Electrical CharacteristicsEarMT Buffers Output lines speakerNot General Purpose I/OLogic level specifications Using a Gpio Pad as Output Using a Gpio Pad as InputUsing the Alarm Output GPIO6 Using the Buzzer Output GPIO7 LED status Device Status Indication of network service availabilityOperating Range VAUX1 power supply VAUX1 power outputRTC Bypass out Mounting UC864-E on your board USB Vbus Usbid Debug of the UC864-E in productionConformity Assessment Issues Safety Recommandations Revision Date Changes Document Change Log
Top Page Image Contents