Tally Genicom 2900 manual 24Operator Manual, Top of Form Nubbin

Page 24

Standard Printing Mode

Fine-tuning the Column Alignment can be done in two ways:

(1)Rotate the Horizontal Vernier Wheel, which is located on the right end of the shaft on which the tractors ride. Depending upon the direction the paper needs to move, you will rotate the wheel either upwards or downwards.

(2)Use the Control Panel. Go Offline, choose Menu, then use the arrow keys to get to the Operator Menu. Press Enter. Use the arrow keys to get to Forms. Press Enter. Use the arrow keys to get to Horz Adjust. Press Enter. Use the arrow keys to increase or decrease the number that appears in the lower right of the LCD. This will shift the position of Column 1.

Step 7.

Set the Top of the Form (TOF). This is done from the Control Panel. If the printer is not on, turn it on now. If necessary, press the Online key until “Offline” is displayed. Use the up or down arrow keys to move the perforation line on the paper so that it is aligned with the nubbin on the tractor door. Once the paper is positioned, press the TOF key. The paper will move downward to the “ready to print” position and the correct print gap will be set based on the form thickness.

	Nubbin
-	- - - - - - - - - - - - - - - - - - - - - - - - - - - -
-

Figure 2 - 6. Top of Form Nubbin

2–24Operator Manual

Image 24

Contents Operator Manual Serial Parallel LAN Operator ManualAcknowledgments Contents Chapter Operator Manual ESC Appendix a Troubleshooting Appendix B Specifications Introduction Operator Manual Preface-9About This Manual Preface-10Operator ManualConventions Setting Up Your Printer Site PreparationUnpacking the Printer Unpacking your printerRepacking Removing the Shipping HardwareInterface Connections and Powering Up Interface ConnectorsInterface Connections Serial/Parallel InterfacesPowering Up Powering Up14Operator Manual Paper System Paper System ComponentsPaper System Components 16Operator Manual TractorsPrint Gap Paper TensionInstalling Ribbon Cartridge Installing the Ribbon Cartridge18Operator Manual LED Indicators Control Panel ComponentsControl Panel Components LCD Liquid Crystal Display20Operator Manual Loading Paper and Printing Standard Printing Mode Loading Paper for Standard Printing Mode Step22Operator Manual Column Alignment Scale 24Operator Manual Print Gap Adjustment Print Gap Profile ModePrint Gap Gap ZoneUsing a Saved Gap Zone Profile Fine-tuning the Automatic Print Gap Setting26Operator Manual Set Print Gap Detect Mode to Manual Manually Adjust Print Gap on Control PanelAfter unlocking the Print Gap keys Manually Setting Print Gap Setting Up Configurations28Operator Manual Run a Print TestControl Panel Display Printer Menus and the Control PanelControl Panel Display Display During Normal Operation30Operator Manual Indicator Paper Weight and Hammer Impact Display When In a MenuControl Panel Key Functions Control Panel Key Functions32Operator Manual TOF Key Top of Form View KeyPrint GAP + and Keys Up and Down Arrow KeysEnter Key Clear Key34Operator Manual Clear Key Config Key OfflineUsing Menus Using MenusControl Panel Menus Categories, Parameters and SelectionsTCP/IP if LAN is installed Example Changing Form Length Using the Menu System Changing Form Length38Operator Manual How to Print a Control Panel Selected Options Report Print Selections ReportOperator Menu Operator Menu ⇒ FontFont Category 40Operator ManualSer/Par Character Set MatrixOcra Density 42Operator Manual Forms Category Operator Menu ⇒ Forms 44Operator ManualQuick Access Print to EOF End Of Form If Print to EOF is onIf Print to EOF is OFF, you have two choices Choice Eject Distance46Operator Manual RibnMon Thresh Ribbon Monitor OperationOperator Menu ⇒ Print Gap Print Gap Category48Operator Manual Fine-Tuning the Print Gap Manually ResetMode 50Operator Manual Detect DistanceVFU Enable Operator Menu ⇒ VFUVFU Category Vertical Format Units VT Channel Vertical Tab ChannelConfig Menu Config Menu ⇒ PrinterPrinter Category 52Operator ManualIO Hold ReportBeeper Mode Beeper Volume54Operator Manual Config Menu ⇒ Codes Codes Category56Operator Manual Print on CRForm Feed at TOF Alt ESC Alternate EscapeCode 7F Print 80 9F HexIgnore Char Sub Char FromConfig Menu ⇒ Configurations Configurations Category58Operator Manual How to label a configuration slot Config Menu ⇒ Serial I/O Serial I/O Category60Operator Manual Status Enquiry DTR Function62Operator Manual DTR PolarityBusy Polarity RTS FunctionConfig Menu ⇒ Parallel I/O Popc Print On Paper CommandParallel I/O Category Bi-DirectionalConfig Menu ⇒ Intellifilter Intellifilter Category64Operator Manual Serial Parallel Twinax/CoaxTCP/IP Menu LAN Interface Only TCP/IP MenuIP Addr Category Gateway CategoryTCP/IP Menu ⇒ Subnet Subnet Category66Operator Manual Test Menu TestMenu ⇒ PatternPattern Category PrintTest Menu ⇒ Fault Override Fault Override CategoryDiag Category 68Operator ManualHelp Menu Help Menu70Operator Manual Faults Appendix a Troubleshooting A-71Fault Correction Procedure MessagesError Messages 72Operator ManualAppendix a Troubleshooting A-73 HammerTimeExplanation Corrective Action74Operator Manual Appendix a Troubleshooting A-75 Paper Problems 76Operator ManualAppendix B Specifications B-77 Industry and Agency StandardsIndustry and Agency Standards 78Operator ManualAppendix B Specifications B-79 EnvironmentEmulations and Fonts 80Operator ManualAppendix B Specifications B-81 Fonts, Languages and CharactersStandard Languages and Character Sets Language SubstitutionsConfigurations, Paper and Speed 82Operator ManualAppendix B Specifications B-83 Daly Drive, Suite 703.833.8700 Chantilly, VA 703.222.7629