Tally Genicom 2900 manual TCP/IP Menu ⇒ Subnet, Subnet Category, 66Operator Manual

Page 66

TCP/IP Menu ⇒ Subnet

Subnet Category

This option allows you to set up the four OCTETS of the Subnet mask. Use the Arrow and Enter keys to select Menu => TCP/IP => Subnet to get here.

Parameter	Option
IP OCTET 1	0-255
IP OCTET 2	0-255
IP OCTET 3	0-255
IP OCTET 4	0-255

Make sure that the LAN cable is attached when the printer is powered on. If it is not, attach the cable and cycle power on the printer.

3–66Operator Manual

Image 66

Contents Operator Manual Serial Parallel LAN Operator ManualAcknowledgments Contents Chapter Operator Manual ESC Appendix a Troubleshooting Appendix B Specifications Introduction Operator Manual Preface-9About This Manual Preface-10Operator ManualConventions Setting Up Your Printer Site PreparationRepacking Unpacking the PrinterUnpacking your printer Removing the Shipping HardwareInterface Connections Interface Connections and Powering UpInterface Connectors Serial/Parallel InterfacesPowering Up Powering Up14Operator Manual Paper System Paper System ComponentsPaper System Components Print Gap 16Operator ManualTractors Paper TensionInstalling Ribbon Cartridge Installing the Ribbon Cartridge18Operator Manual Control Panel Components LED IndicatorsControl Panel Components LCD Liquid Crystal Display20Operator Manual Loading Paper and Printing Standard Printing Mode Loading Paper for Standard Printing Mode Step22Operator Manual Column Alignment Scale 24Operator Manual Print Gap Print Gap AdjustmentPrint Gap Profile Mode Gap ZoneUsing a Saved Gap Zone Profile Fine-tuning the Automatic Print Gap Setting26Operator Manual Set Print Gap Detect Mode to Manual Manually Adjust Print Gap on Control PanelAfter unlocking the Print Gap keys 28Operator Manual Manually Setting Print GapSetting Up Configurations Run a Print TestControl Panel Display Printer Menus and the Control PanelControl Panel Display Display During Normal Operation30Operator Manual Indicator Paper Weight and Hammer Impact Display When In a MenuControl Panel Key Functions Control Panel Key Functions32Operator Manual Print GAP + and Keys TOF Key Top of FormView Key Up and Down Arrow KeysEnter Key Clear Key34Operator Manual Clear Key Config Key OfflineControl Panel Menus Using MenusUsing Menus Categories, Parameters and SelectionsTCP/IP if LAN is installed Example Changing Form Length Using the Menu System Changing Form Length38Operator Manual How to Print a Control Panel Selected Options Report Print Selections ReportFont Category Operator MenuOperator Menu ⇒ Font 40Operator ManualSer/Par Character Set MatrixOcra Density 42Operator Manual Forms Category Operator Menu ⇒ Forms 44Operator ManualIf Print to EOF is OFF, you have two choices Choice Quick AccessPrint to EOF End Of Form If Print to EOF is on Eject Distance46Operator Manual RibnMon Thresh Ribbon Monitor OperationOperator Menu ⇒ Print Gap Print Gap Category48Operator Manual Fine-Tuning the Print Gap Manually ResetMode 50Operator Manual Detect DistanceVFU Category Vertical Format Units VFU EnableOperator Menu ⇒ VFU VT Channel Vertical Tab ChannelPrinter Category Config MenuConfig Menu ⇒ Printer 52Operator ManualIO Hold ReportBeeper Mode Beeper Volume54Operator Manual Config Menu ⇒ Codes Codes CategoryForm Feed at TOF 56Operator ManualPrint on CR Alt ESC Alternate EscapeIgnore Char Code 7FPrint 80 9F Hex Sub Char FromConfig Menu ⇒ Configurations Configurations Category58Operator Manual How to label a configuration slot Config Menu ⇒ Serial I/O Serial I/O Category60Operator Manual Status Enquiry DTR FunctionBusy Polarity 62Operator ManualDTR Polarity RTS FunctionParallel I/O Category Config Menu ⇒ Parallel I/OPopc Print On Paper Command Bi-Directional64Operator Manual Config Menu ⇒ IntellifilterIntellifilter Category Serial Parallel Twinax/CoaxIP Addr Category TCP/IP Menu LAN Interface OnlyTCP/IP Menu Gateway CategoryTCP/IP Menu ⇒ Subnet Subnet Category66Operator Manual Pattern Category Test MenuTestMenu ⇒ Pattern PrintDiag Category Test Menu ⇒ Fault OverrideFault Override Category 68Operator ManualHelp Menu Help Menu70Operator Manual Fault Correction Procedure FaultsAppendix a Troubleshooting A-71 MessagesError Messages 72Operator ManualAppendix a Troubleshooting A-73 HammerTimeExplanation Corrective Action74Operator Manual Appendix a Troubleshooting A-75 Paper Problems 76Operator ManualAppendix B Specifications B-77 Industry and Agency StandardsIndustry and Agency Standards 78Operator ManualAppendix B Specifications B-79 EnvironmentEmulations and Fonts 80Operator ManualStandard Languages and Character Sets Appendix B Specifications B-81Fonts, Languages and Characters Language SubstitutionsConfigurations, Paper and Speed 82Operator ManualAppendix B Specifications B-83 Daly Drive, Suite 703.833.8700 Chantilly, VA 703.222.7629