Tally Genicom 2900 manual Control Panel Key Functions, 32Operator Manual

Page 32

Control Panel Key Functions

Control Panel Key Functions

Online Key

This key toggles the printer between Online and Offline states, or exits from the menu directly to an Online state. When the printer is Online, the indicator will light. In the Offline state, you may change parameter selections, load paper, and so on.

LF Key (Line Feed)

This key advances the paper one line. It performs the same function whether the printer is Online or Offline. You may auto-repeat this command by holding down the key.

 

While Offline With Data Buffered

 

Any buffered data falling in the next line (as defined by the

 

current LPI setting), prints. This repeats upon subsequent LF

 

keystrokes as long as there is data in the buffers. If pressed

 

while printing is in progress, the printer ignores the key

Figure 3 - 3. Control Panel

command and maintains the Top of Form position.

 

While Offline With No Data Buffered

Paper advances one line. While printing is in progress, the printer ignores the command and maintains the Top of Form position.

While In A Fault Condition

Paper advances one line. No data is printed and the Top of Form position moves down one line. This allows the use of the LF Key to advance paper while in a Paper Out condition without printing any buffered data.

FF Key (Form Feed)

This key performs the same function whether the printer is Online or Offline.

While Offline With Data Buffered

Any buffered data falling between the current form position and the top of the next form (as defined by the current Form Length setting), prints. This func- tion repeats upon subsequent FF keystrokes as long as there is data in the buffers. The printer ignores the command while printing is in progress and maintains the Top of Form position.

While Offline With No Data Buffered

Paper advances to the top of the next form. The printer ignores this command while printing is in progress and maintains the Top of Form position.

3–32Operator Manual

Image 32
Contents Operator Manual Serial Parallel LAN Operator ManualAcknowledgments Contents Chapter Operator Manual ESC Appendix a Troubleshooting Appendix B Specifications Introduction Operator Manual Preface-9Conventions About This ManualPreface-10Operator Manual Setting Up Your Printer Site PreparationUnpacking the Printer Unpacking your printerRepacking Removing the Shipping HardwareInterface Connections and Powering Up Interface ConnectorsInterface Connections Serial/Parallel Interfaces14Operator Manual Powering UpPowering Up Paper System Components Paper SystemPaper System Components 16Operator Manual TractorsPrint Gap Paper TensionInstalling Ribbon Cartridge Installing the Ribbon Cartridge18Operator Manual LED Indicators Control Panel ComponentsControl Panel Components LCD Liquid Crystal Display20Operator Manual Loading Paper and Printing 22Operator Manual Standard Printing ModeLoading Paper for Standard Printing Mode Step Column Alignment Scale 24Operator Manual Print Gap Adjustment Print Gap Profile ModePrint Gap Gap Zone26Operator Manual Using a Saved Gap Zone ProfileFine-tuning the Automatic Print Gap Setting After unlocking the Print Gap keys Set Print Gap Detect Mode to ManualManually Adjust Print Gap on Control Panel Manually Setting Print Gap Setting Up Configurations28Operator Manual Run a Print TestControl Panel Display Printer Menus and the Control Panel30Operator Manual Control Panel DisplayDisplay During Normal Operation Indicator Paper Weight and Hammer Impact Display When In a Menu32Operator Manual Control Panel Key FunctionsControl Panel Key Functions TOF Key Top of Form View KeyPrint GAP + and Keys Up and Down Arrow Keys34Operator Manual Enter KeyClear Key Clear Key Config Key OfflineUsing Menus Using MenusControl Panel Menus Categories, Parameters and SelectionsTCP/IP if LAN is installed 38Operator Manual Example Changing Form Length Using the Menu SystemChanging Form Length How to Print a Control Panel Selected Options Report Print Selections ReportOperator Menu Operator Menu ⇒ FontFont Category 40Operator ManualOcra Density Ser/Par Character SetMatrix 42Operator Manual Forms Category Operator Menu ⇒ Forms 44Operator ManualQuick Access Print to EOF End Of Form If Print to EOF is onIf Print to EOF is OFF, you have two choices Choice Eject Distance46Operator Manual RibnMon Thresh Ribbon Monitor Operation48Operator Manual Operator Menu ⇒ Print GapPrint Gap Category Mode Fine-Tuning the Print Gap ManuallyReset 50Operator Manual Detect DistanceVFU Enable Operator Menu ⇒ VFUVFU Category Vertical Format Units VT Channel Vertical Tab ChannelConfig Menu Config Menu ⇒ PrinterPrinter Category 52Operator ManualIO Hold Report54Operator Manual Beeper ModeBeeper Volume Config Menu ⇒ Codes Codes Category56Operator Manual Print on CRForm Feed at TOF Alt ESC Alternate EscapeCode 7F Print 80 9F HexIgnore Char Sub Char From58Operator Manual Config Menu ⇒ ConfigurationsConfigurations Category How to label a configuration slot 60Operator Manual Config Menu ⇒ Serial I/OSerial I/O Category Status Enquiry DTR Function62Operator Manual DTR PolarityBusy Polarity RTS FunctionConfig Menu ⇒ Parallel I/O Popc Print On Paper CommandParallel I/O Category Bi-DirectionalConfig Menu ⇒ Intellifilter Intellifilter Category64Operator Manual Serial Parallel Twinax/CoaxTCP/IP Menu LAN Interface Only TCP/IP MenuIP Addr Category Gateway Category66Operator Manual TCP/IP Menu ⇒ SubnetSubnet Category Test Menu TestMenu ⇒ PatternPattern Category PrintTest Menu ⇒ Fault Override Fault Override CategoryDiag Category 68Operator ManualHelp Menu Help Menu70Operator Manual Faults Appendix a Troubleshooting A-71Fault Correction Procedure MessagesError Messages 72Operator ManualAppendix a Troubleshooting A-73 HammerTimeExplanation Corrective Action74Operator Manual Appendix a Troubleshooting A-75 Paper Problems 76Operator ManualAppendix B Specifications B-77 Industry and Agency StandardsIndustry and Agency Standards 78Operator ManualAppendix B Specifications B-79 EnvironmentEmulations and Fonts 80Operator ManualAppendix B Specifications B-81 Fonts, Languages and CharactersStandard Languages and Character Sets Language SubstitutionsConfigurations, Paper and Speed 82Operator ManualAppendix B Specifications B-83 Daly Drive, Suite 703.833.8700 Chantilly, VA 703.222.7629