Tally Genicom 2900 manual How to label a configuration slot

Page 59

Config Menu ⇒ Configurations

How to label a configuration slot

•Make sure the printer is Offline.

•Press the Menu key to enter Menu mode.

•Use the Up and Down Arrow keys to get to the Config menu, and then press Enter.

•Use the Up and Down Arrow keys until the display reads Configura- tions, then press Enter.

•Use the Up and Down Arrow keys until you see Config n label, where n is the number of the configuration you want to label (1-10). Press Enter.

•A cursor appears underneath the first letter (C). Use the Up and Down Arrow keys to scroll to the number or letter you want to use. Repeat for up to 15 characters, pressing Enter after each letter. You must press Enter 15 times even if your label is shorter.

•Press Clear or Menu to save it. Now, when you use SAVE or LOAD, this configuration name appears in the slot you've chosen.

Chapter 3: Printer Menus and the Control Panel 3–59

Image 59

Contents Operator Manual Operator Manual Serial Parallel LANAcknowledgments Contents Chapter Operator Manual ESC Appendix a Troubleshooting Appendix B Specifications Operator Manual Preface-9 IntroductionConventions About This ManualPreface-10Operator Manual Site Preparation Setting Up Your PrinterRemoving the Shipping Hardware Unpacking the PrinterUnpacking your printer RepackingSerial/Parallel Interfaces Interface Connections and Powering UpInterface Connectors Interface Connections14Operator Manual Powering UpPowering Up Paper System Components Paper SystemPaper System Components Paper Tension 16Operator ManualTractors Print GapInstalling the Ribbon Cartridge Installing Ribbon Cartridge18Operator Manual LCD Liquid Crystal Display LED IndicatorsControl Panel Components Control Panel Components20Operator Manual Loading Paper and Printing 22Operator Manual Standard Printing ModeLoading Paper for Standard Printing Mode Step Column Alignment Scale 24Operator Manual Gap Zone Print Gap AdjustmentPrint Gap Profile Mode Print Gap26Operator Manual Using a Saved Gap Zone ProfileFine-tuning the Automatic Print Gap Setting After unlocking the Print Gap keys Set Print Gap Detect Mode to ManualManually Adjust Print Gap on Control Panel Run a Print Test Manually Setting Print GapSetting Up Configurations 28Operator ManualPrinter Menus and the Control Panel Control Panel Display30Operator Manual Control Panel DisplayDisplay During Normal Operation Display When In a Menu Indicator Paper Weight and Hammer Impact32Operator Manual Control Panel Key FunctionsControl Panel Key Functions Up and Down Arrow Keys TOF Key Top of FormView Key Print GAP + and Keys34Operator Manual Enter KeyClear Key Offline Clear Key Config KeyCategories, Parameters and Selections Using MenusUsing Menus Control Panel MenusTCP/IP if LAN is installed 38Operator Manual Example Changing Form Length Using the Menu SystemChanging Form Length Print Selections Report How to Print a Control Panel Selected Options Report40Operator Manual Operator MenuOperator Menu ⇒ Font Font CategoryOcra Density Ser/Par Character SetMatrix 42Operator Manual Forms Category 44Operator Manual Operator Menu ⇒ FormsEject Distance Quick AccessPrint to EOF End Of Form If Print to EOF is on If Print to EOF is OFF, you have two choices Choice46Operator Manual Ribbon Monitor Operation RibnMon Thresh48Operator Manual Operator Menu ⇒ Print GapPrint Gap Category Mode Fine-Tuning the Print Gap ManuallyReset Detect Distance 50Operator ManualVT Channel Vertical Tab Channel VFU EnableOperator Menu ⇒ VFU VFU Category Vertical Format Units52Operator Manual Config MenuConfig Menu ⇒ Printer Printer CategoryReport IO Hold54Operator Manual Beeper ModeBeeper Volume Codes Category Config Menu ⇒ CodesAlt ESC Alternate Escape 56Operator ManualPrint on CR Form Feed at TOFSub Char From Code 7FPrint 80 9F Hex Ignore Char58Operator Manual Config Menu ⇒ ConfigurationsConfigurations Category How to label a configuration slot 60Operator Manual Config Menu ⇒ Serial I/OSerial I/O Category DTR Function Status EnquiryRTS Function 62Operator ManualDTR Polarity Busy PolarityBi-Directional Config Menu ⇒ Parallel I/OPopc Print On Paper Command Parallel I/O CategorySerial Parallel Twinax/Coax Config Menu ⇒ IntellifilterIntellifilter Category 64Operator ManualGateway Category TCP/IP Menu LAN Interface OnlyTCP/IP Menu IP Addr Category66Operator Manual TCP/IP Menu ⇒ SubnetSubnet Category Print Test MenuTestMenu ⇒ Pattern Pattern Category68Operator Manual Test Menu ⇒ Fault OverrideFault Override Category Diag CategoryHelp Menu Help Menu70Operator Manual Messages FaultsAppendix a Troubleshooting A-71 Fault Correction Procedure72Operator Manual Error MessagesHammerTimeExplanation Corrective Action Appendix a Troubleshooting A-7374Operator Manual Appendix a Troubleshooting A-75 76Operator Manual Paper ProblemsIndustry and Agency Standards Appendix B Specifications B-7778Operator Manual Industry and Agency StandardsEnvironment Appendix B Specifications B-7980Operator Manual Emulations and FontsLanguage Substitutions Appendix B Specifications B-81Fonts, Languages and Characters Standard Languages and Character Sets82Operator Manual Configurations, Paper and SpeedAppendix B Specifications B-83 Daly Drive, Suite 703.833.8700 Chantilly, VA 703.222.7629