Seiko FB 390 user manual Command Code Summary, USB Interface, Epson Emulation

Page 37

USB Interface

USB 2.0 Full-Speed.

The following table provides the standardized contact terminating assignments by number and electrical value for Series “A” and Series “B” connectors.

Contact Number	Signal Name	Typical Wiring Assignment
1	VBUS	Red

2	D-	White
3	D+	Green

4	GND	Black
Shell	Shield	Wire

Command Code Summary

Epson Emulation

	Name	Code
	Name	(Symbol)
		(Symbol)
	Print and Line Feed Execution

	Carriage Return	CR
	Line Feed	LF
	n/180” Line Feed	ESC J
	n/180” Reverse Line Feed	ESC j
	Format Control

	Set 1/8” Line Spacing	ESC 0
	Set 1/6” Line Spacing	ESC 2
	Set n/180” Line Spacing	ESC 3
	Set n/60” Line Spacing	ESC A
	Set n/360” Line Spacing	ESC +
	Form Feed	FF
	Set Form Length in Lines	ESC C
	Set Form Length in Inches	ESC C NUL
	Set Form Length in Defined Unit	ESC ( C
	Select Skip-Over-Perforation	ESC N n
	Cancel Skip-Over-Perforation	ESC O

	Vertical Tab	VT
	Set Vertical Tab Positions	ESC B
	Select a VFU Channel	ESC /
	Select VFU Positions	ESC b
	Set right Margin	ESC Q
	Set Left Margin	ESC l

Code (Hex.)

0Dh

0Ah

1Bh 4Ah

1Bh 6Ah

1Bh 30h

1Bh 32h

1Bh 32h

1Bh 41h

1Bh 2Bh

0Ch

1Bh 43h

1Bh 43h 00h

1Bh 28h 43h

1Bh 4Eh

1Bh 4Fh

0Bh

1Bh 42h

1Bh 2Fh

1Bh 62h

1Bh 51h

1Bh 6Ch

Code (Dec.)

13d

10d

27d 74d

27d 106d

27d 48d

27d 50d

27d 51d

27d 65d

27d 43d

12 d

27d 67d

27d 67d 0d

27d 40d 67d

27d 78d

27d 79d

11d

27d 66d

27d 47d

27d 98d

27d 81d

27d 108d

32

Image 37

Contents Seiko Precision Important Safety Instructions Table of Contents To enter the Setup Menu System and change the settings Epson Emulation Select Code Pages Overview FeaturesHigh Resolution Graphics Automatic Interface SwitchingUser- Friendly Control Panel EmulationUnpacking PreparationMain parts of printer rear view Paper feed knob Parts IdentificationInstalling the Front Table Extension Tray InstallationInstalling and Replacing the Ribbon Cassette Make sure of the following Connecting the Interface CableConnecting to the Power Source Using the Parallel Interface and the USB InterfaceConnecting the Power Cord Turning the Power on and offAdjusting the gap adjust lever Paper Thickness AdjustmentLoading paper Position Copies ThicknessLoading Cut Sheet Paper Loading Tractor Paper Using Tractor PaperPage Page 15 Tractor paper tear-off Tearing off Tractor PaperPrinting from Your Software Setting Up Your Printer To Work With SoftwareControl Panel Indicator LED OffControl Panel Keys and LEDs Basic Control Panel Operations Top of Form Adjustment ModeUsing the Setup Menu System Tear-off Adjustment ModeTo exit without saving, just turn the printer OFF To exit without saving, just turn off the printerTo exit the Setup Menu System To enter the Setup Menu System and change the settingsTo print the current settings Printing the Current Setting ReportSeiko Precision FB-390 Setup Menu System Options of the Setup Menu SystemFont Options DescriptionUsing the Self Test Functions Restoring Factory Printer SettingsMaintenance Printing Test H pattern Slide Pattern Printing TestPrint Mode Hex Dump ModeCleaning the Cabinet Maintenance and Fault FindingAppendix a Intervals and Materials for Cleaning Problems And SolutionsError Cause Remedy Error LED on the Control PanelAppendix B SpecificationsGeneral Print HeadPaper MechanismMultipart Dot Spacing Max No Character Printing Print mode Print mode specifications×H inches Parallel Interface Graphic Print SpecificationsUSB Interface Command Code SummaryEpson Emulation Character Set Name Code SymbolDownload Character Graphics ModeBit-Image Input Data ControlFormat Select Code PagesCode No D2 d3 HEX Name