Seiko TM-U590/U590P manual Parallel interface specification, Dip Switch Setting A-3

Page 51

Parallel interface specification

Set 1

	SW	Function	ON	OFF

	1-1	Auto line feed	Always enabled	Always disabled

	1-2	Receive buffer capacity	69 bytes	4K bytes

	1-3 ~	Undefined	—	—
	1-8	Undefined	—	—
	1-8

Set 2

	SW	Function	ON	OFF

		Handshaking (BUSY	•Receive buffer full	•Off-line
	2-1	Handshaking (BUSY	•Receive buffer full	•Receive buffer full
	2-1	condition)	•Reading data	•Receive buffer full
		condition)	•Reading data	•Reading data
				•Reading data

	2-2	Reserved	Fixed to Off
	2-2	(Do not change settings)	Fixed to Off

	2-3 ~	Undefined	—
	2-4	Undefined	—
	2-4

	2-5 ~	Reserved	Fixed to Off
	2-7	(Do not change settings)	Fixed to Off

	2-8	I/F pin 31 reset signal	Fixed to On
	2-8	(Do not change settings)	Fixed to On

Notes:

•Changes in DIP switch settings (excluding switch 2-8 interface reset signal) are recognized only when the printer power is turned on or when the printer is reset by using the interface. If the DIP switch setting is changed after the printer power is turned on, the change does not take effect until the printer is turned on again or is reset.

•If you turn on DIP switch 2-8 while the printer is turned on, the printer may be reset, depending on the signal state. DIP switches should not be changed while the printer power is on.

Dip Switch Setting A-3

Image 51

Contents TM-U590/U590P Labels Printer Parts and LabelsValidating and Verifying Checks Setting Up the PrinterSolving Problems Quick ReferencePage FCC Compliance Statement For American UsersIii Declaration of Conformity EMI and Safety Standards Applied Setting Up and Using About This ManualReference Options FeaturesAccessory IntroductionOrdering Ribbon Cassettes Contents Appendix B Epson Sales Subsidiaries Unpacking Setting Up the PrinterRemoving the protective material 2Setting Up the PrinterConnecting the computer Connecting the Cables and Grounding the Printer4Setting Up the Printer Connecting the Drawer Anschließen der Lade 6Setting Up the PrinterGrounding the Printer Connecting the Display Module8Setting Up the Printer Connecting the Power SupplyPage 10Setting Up the Printer Installing the Ribbon CassetteKnob Running the self test Using the Power Switch Cover12Setting Up the Printer Self TestCompleted DIP Switch SettingsRemoving the Paper Guide Slide the paper guide to the left to remove it Control Panel Using the PrinterUsing the Printer Operating the Control PanelsIndicator lights 2Using the PrinterPanel lights Slip Paper Handling Using the Micr Reader Option 4Using the PrinterReading Micr characters on personal checks Using the Printer Printing problems TroubleshootingTroubleshooting General problemsLine of dots is missing in the printout 2TroubleshootingPrinter sounds like it is printing, but nothing is printed Printout is faintCleaning procedure Cleaning the Optional Micr MechanismPaper handling problems Mica cleaning method Recommended4Troubleshooting Adhesive Cleaning SheetAdhesice cleaning sheet Refer to Figure Explanatin of a cleaning sheetCommand code sequence Moistened Cleaning sheetHexadecimal Dump 6TroubleshootingPrinting Specifications Reference InformationPaper Micr Reader Option Ribbon SpecificationsPaper feed speed Paper SpecificationsPaper feed method Paper feed pitchAmbient temperature and copy capability Paper4Reference Information Copy capability and paper thickness 6Reference Information Reference Information Reliability Electrical CharacteristicsMtbf Mcbf Temperature Environmental ConditionsHumidity Serial interface specification Dip Switch SettingSetting the DIP Switches DIP switch functions2Dip Switch Setting Dip Switch Setting A-3 Parallel interface specification4Dip Switch Setting Changing the DIP switch settingsEpson Sales Subsidiaries B-1 Epson Sales Subsidiaries2EPSON Sales Subsidiaries