Seiko TM-U590/U590P manual 2Dip Switch Setting

Page 50

Transmission Speed

Transmission Speed (BPS)-bits per second

1-7

1-8

 

 

 

2400

ON

ON

 

 

 

4800

OFF

ON

 

 

 

9600

ON

OFF

 

 

 

19200

OFF

OFF

 

 

 

Set 2

SW

Function

ON

OFF

 

 

 

 

2-1

Handshaking (BUSY

Receive buffer full

Off line or

condition)

receive buffer full

 

 

 

 

 

 

2-2

Customer display

Connected

Not connected

(DM-D) connection

 

 

 

 

 

 

 

2-3~

Undefined

—

 

2-4

 

 

 

 

 

 

 

 

2.5~

Internal use

Fixed to Off

 

2.6

 

 

 

 

 

 

 

 

 

2-7*

I/F pin 6 reset signal

Enabled

Disabled

 

 

 

 

2-8*

I/F pin 25 reset signal

Enabled

Disabled

 

 

 

 

*With a RS-485 serial interface specification (a dealer option), DIP switches 2-7 and 2-8 are ignored.

Notes:

•Changes in DIP switch settings (excluding switches 2-7 and 2-8 interface reset signals) are recognized only when the printer power is turned on or when the printer is reset by using the interface. If the DIP switch setting is changed after the printer power is turned on, the change does not take effect until the printer is turned on again or is reset.

•If you turn on DIP switch 2-7 or 2-8 while the printer is turned on, the printer may be reset, depending on the signal state. DIP switches should not be changed while the printer power is on.

A-2Dip Switch Setting

Page 49 Page 51
Image 50
Page 49 Page 51
Contents TM-U590/U590P Printer Parts and Labels LabelsQuick Reference Setting Up the PrinterSolving Problems Validating and Verifying ChecksPage Iii FCC Compliance StatementFor American Users Declaration of Conformity EMI and Safety Standards Applied Reference Setting Up and UsingAbout This Manual Introduction FeaturesAccessory OptionsOrdering Ribbon Cassettes Contents Appendix B Epson Sales Subsidiaries Setting Up the Printer Unpacking2Setting Up the Printer Removing the protective materialConnecting the Cables and Grounding the Printer Connecting the computer4Setting Up the Printer Connecting the Drawer 6Setting Up the Printer Anschließen der LadeConnecting the Display Module Grounding the PrinterConnecting the Power Supply 8Setting Up the PrinterPage Installing the Ribbon Cassette 10Setting Up the PrinterKnob Self Test Using the Power Switch Cover12Setting Up the Printer Running the self testDIP Switch Settings CompletedRemoving the Paper Guide Slide the paper guide to the left to remove it Operating the Control Panels Using the PrinterUsing the Printer Control PanelPanel lights Indicator lights2Using the Printer Slip Paper Handling Reading Micr characters on personal checks Using the Micr Reader Option4Using the Printer Using the Printer General problems TroubleshootingTroubleshooting Printing problemsPrintout is faint 2TroubleshootingPrinter sounds like it is printing, but nothing is printed Line of dots is missing in the printoutMica cleaning method Recommended Cleaning the Optional Micr MechanismPaper handling problems Cleaning procedureAdhesive Cleaning Sheet 4TroubleshootingMoistened Cleaning sheet Explanatin of a cleaning sheetCommand code sequence Adhesice cleaning sheet Refer to Figure6Troubleshooting Hexadecimal DumpPaper Printing SpecificationsReference Information Ribbon Specifications Micr Reader OptionPaper feed pitch Paper SpecificationsPaper feed method Paper feed speed4Reference Information Ambient temperature and copy capabilityPaper Copy capability and paper thickness 6Reference Information Reference Information Electrical Characteristics ReliabilityMtbf Mcbf Humidity TemperatureEnvironmental Conditions DIP switch functions Dip Switch SettingSetting the DIP Switches Serial interface specification2Dip Switch Setting Parallel interface specification Dip Switch Setting A-3Changing the DIP switch settings 4Dip Switch SettingEpson Sales Subsidiaries Epson Sales Subsidiaries B-12EPSON Sales Subsidiaries
Top Page Image Contents