Universal Laser Systems CLP-100NI-NPRT manual Installing the PRE-INKED Roll

Page 10

QUICK START

5 - Press the Inking System Assembly towards the Print Drum and adjust the Position Adjusting Screw “F” until the Knurled Drive Wheel “G” makes positive contact with the Friction Bearer “H” on the Print Drum. When the Pivot Arm Adjustment Knob “C” is tightened, the Knurled Drive Wheel should only contact the Friction Bearer Ring with enough pressure to drive positively when the print drum is rotated.

This adjustment procedure also controls the Transfer Roll con- tact with the printing dies. Excessive engagement pressure

should be avoided as this will cause unnecessary drag on theFIGURE 12 print drum and result in smudged impressions.

INSTALLING THE PRE-INKED ROLL

Warning: Non-Porous inks contain flammable solvents. Do not smoke or handle these rolls in the presence of sparks or open flames. Inks will also stain clothing, furniture, carpeting and your hands. Rubber gloves should be worn during the following procedures.

The ink roll you install on the coder must be properly pre-inked. If your coder was supplied with a dry XF Neoprene ink roll, refer to the Maintenance Section page 27 for inking instructions.

Rollers that have been pre-inked at the factory are normally slightly oversaturated with ink to compensate for potential solvent loss during shipping and storage. If you received a pre-inked ink roll with your coder, it is important to examine the roll prior to installation. The ink roll should be thoroughly saturated with ink but not dripping wet. Excess ink can be easily removed by lightly rolling the ink roll across a clean piece of absorbent paper.

1 - To install the pre-inked roll, first turn the Ink Roll Eccen- tric Adjusting Knob “I” to the “MIN” position.

This moves the ink roller axle away from the Transfer Roll and enables the ink roll to be installed without interference with the Transfer Roll during reassembly of the inking sys- tem.

FIGURE 13

2 - Loosen the Knurled Pivot Arm Knob “C” & swing the Inking System Assembly “A” away from Print Drum.

FIGURE 14

10

Image 10
Contents Installation Operation Maintenance Stenciling & MarkingPreface Specifications Important NotePreface Coder SpecificationsQuick Start Specifications Conveyor Line Printer Specifications TOP Mount SeriesConveyor Line Printer Specifications Side Mount Series Model Shown CLP-200NI-NPLSMounting Configuration Indexing and NON-INDEXING ModelsRIBtype Printing Dies XF Neoprene INK Rolls INK RollsType MT INK Rolls Installing the Inking System Assembly Quick StartInstalling the PRE-INKED Roll Knurled Drive Wheel Cover is very loose fitting Quick Start Hold the Drive Wheel Cover and Inking System Cover in place Installing the Printing Dies Adjusting the INK Roll Eccentric Basic Principles of Operation Using the 4 OZ. Reservoir INK CartridgesNON-POROUS Inking System Selecting AN Appropriate INK INK Drying Time Considerations WEB Printing Mounting the Coder Special WEB Printing Applications Gang Mounting Carton Printing Carton AlignmentClearance 1/4 DIE Positioning for Indexing Applications Carton Printing Maintenance PRE-INKING a NEW INK RollCleaning the Transfer Roll Cleaning the CoderCleaning the Printing Dies Pivot ARM & Inking System Assembly Conversion Tension ARM Assembly Conversion Print Drum Index Mechanism Conversion Print Drum Axle Brass TIP Recess Area SET Screw Replacing Print Drum Index Springs Removing and Replacing Index Block B Lift Index Block B straight up to remove Inking System Assembly Maintenance MOUNTINGARM, CLP CE Guard NON-POROUS Conveyor Line Printer Assembly NON-POROUS Conveyor Line Printer Parts List NON-POROUS Conveyor Line Printer Inking System Assembly NON-POROUS Conveyor Line Printer Inking System Parts List CLP NON-POROUS Inking System BaseplateFriction Bearer Ring Square CUT Snap Ring