Universal Laser Systems CLP-100NI-NPRT Indexing and NON-INDEXING Models, Mounting Configuration

Page 6

SPECIFICATIONS

INDEXING AND NON-INDEXING MODELS

Universal Non-Porous Conveyor Line Printers are available in both indexing and non-indexing models.

Indexing coders contain a print drum spring return mechanism which provides print registration capabilities when carton printing (see Figure 1). As the trailing edge of a carton passes the coder, the print drum automatically rotates back to the same starting or “home” position. There must be adequate space between cartons at any given line speed for this mechanism to work properly. Print- ing with an indexing coder will allow the imprint on each carton to be registered in the same position relative to the leading edge of the carton. The code will repeat every 18" down the length of the car- ton.

Non-indexing coders have print drums which simply rotate on bearings with no spring return mechanism. These coders are nor- mally used for web printing applications where the print drum stays in contact with the web at all times. If used in carton printing appli- cations, when the trailing edge of a carton passes the coder, the print drum rotation stops at a random position. When the next car- ton engages the print drum, the code will begin printing at a random position relative to the leading edge of the carton and repeat the code every 18" down the length of the carton.

SPRING RETURN

MECHANISM

FIGURE 1

MOUNTING CONFIGURATION

The mounting configuration of a coder is determined by how the machine is designed to be mounted in relation to the product and its movement. All references to mounting configuration are made as though you are viewing the production line with the product moving away from you. Universal Conveyor Line Printers are available from the factory in 4 different mounting configurations as shown in Figures 2 and 3.

RIGHT HAND SIDE MOUNT

LEFT HAND SIDE MOUNT

FIGURE 2

LEFT HAND

RIGHT HAND

TOP MOUNT

TOP MOUNT

FIGURE 3

Note: Due to the symmetrical design of the Inking System on the Non-Porous Conveyor Line Printer, the Right Hand and Left Hand mounting configurations are field convertible. Due to the location of the ports for the 4 Oz. Reservoir Ink Cartridges, Top Mount and Side Mount orientations cannot be field converted and must be properly specified when ordering.

6

Image 6
Contents Installation Operation Maintenance Stenciling & MarkingPreface Specifications Important NoteCoder Specifications PrefaceQuick Start Specifications Conveyor Line Printer Specifications TOP Mount SeriesConveyor Line Printer Specifications Side Mount Series Model Shown CLP-200NI-NPLSMounting Configuration Indexing and NON-INDEXING ModelsRIBtype Printing Dies INK Rolls XF Neoprene INK RollsType MT INK Rolls Installing the Inking System Assembly Quick StartInstalling the PRE-INKED Roll Knurled Drive Wheel Cover is very loose fitting Quick Start Hold the Drive Wheel Cover and Inking System Cover in place Installing the Printing Dies Adjusting the INK Roll Eccentric Using the 4 OZ. Reservoir INK Cartridges Basic Principles of OperationNON-POROUS Inking System Selecting AN Appropriate INK INK Drying Time Considerations WEB Printing Mounting the Coder Special WEB Printing Applications Gang Mounting Carton Printing Carton AlignmentClearance 1/4 DIE Positioning for Indexing Applications Carton Printing Maintenance PRE-INKING a NEW INK RollCleaning the Transfer Roll Cleaning the CoderCleaning the Printing Dies Pivot ARM & Inking System Assembly Conversion Tension ARM Assembly Conversion Print Drum Index Mechanism Conversion Print Drum Axle Brass TIP Recess Area SET Screw Replacing Print Drum Index Springs Removing and Replacing Index Block B Lift Index Block B straight up to remove Inking System Assembly Maintenance MOUNTINGARM, CLP CE Guard NON-POROUS Conveyor Line Printer Assembly NON-POROUS Conveyor Line Printer Parts List NON-POROUS Conveyor Line Printer Inking System Assembly NON-POROUS Conveyor Line Printer Inking System Parts List CLP NON-POROUS Inking System BaseplateFriction Bearer Ring Square CUT Snap Ring