Universal Laser Systems CLP-100NI-NPRT manual Pivot ARM & Inking System Assembly Conversion

Page 30

MAINTENANCE

MOUNTING CONFIGURATION CONVERSION

LEFTHAND/RIGHTHAND FIELD CONVERSION

Mounting configuration conversion involves the “mirror image” reversal of the pivot arm assembly that holds the inking system and the tension arm assembly which provides the printing pressure. Indexing printers require the additional reversal of the index ramp and repositioning of the index ring.

Universal Non-Porous CLP Coders are assembled at the factory for either right-hand or left-hand mounting. If field conversion is required, the following steps will guide you through the conversion process.

PIVOT ARM & INKING SYSTEM ASSEMBLY CONVERSION

1- Loosen the Pivot Arm Adjustment Knob and rotate the Inking System away from the Print Drum slightly. 2- Remove the Inking System Assembly from the coder by removing the 2 socket head cap screws on

the underneath side of the Pivot Arm.

3- Remove the Pivot Screw and lift the tension adjustment assembly off of the coder.

4- Remove the Pivot Arm Cap and lift the Pivot Arm assembly off it’s axle.

5- Reinstall the Pivot Arm on the axle in the opposite or “mirrored” orientation and replace the Pivot Arm Cap.

6- Remove the Position Adjusting Screw and reinstall in the reverse position.

7- Replace the tension adjusting assembly and the Pivot Screw.

INKING SYSTEM

 

ASSEMBLY

 

PIVOT ARM

 

PIVOT SCREW

TENSION

PIVOT ARM CAP

ADJUSTMENT

ASSEMBLY

 

POSITION ADJUSTING

SCREW

 

PIVOT ARM

 

ADJUSTMENT KNOB

 

LEFT HAND

RIGHT HAND

CONFIGURATION

CONFIGURATION

FIGURE 54

8 - Remove the Baseplate Plug from the bottom side of the Inking System Assembly Baseplate (See Figure 55).

9 - Reinstall the Baseplate Plug in the threaded hole on the opposite side of the Baseplate. Thread the Plug into the Baseplate only until the flush with the Baseplate surface.

30

Image 30
Contents Installation Operation Maintenance Stenciling & MarkingPreface Specifications Important NoteCoder Specifications PrefaceQuick Start Specifications Conveyor Line Printer Specifications TOP Mount SeriesConveyor Line Printer Specifications Side Mount Series Model Shown CLP-200NI-NPLSMounting Configuration Indexing and NON-INDEXING ModelsRIBtype Printing Dies INK Rolls XF Neoprene INK RollsType MT INK Rolls Installing the Inking System Assembly Quick StartInstalling the PRE-INKED Roll Knurled Drive Wheel Cover is very loose fitting Quick Start Hold the Drive Wheel Cover and Inking System Cover in place Installing the Printing Dies Adjusting the INK Roll Eccentric Using the 4 OZ. Reservoir INK Cartridges Basic Principles of OperationNON-POROUS Inking System Selecting AN Appropriate INK INK Drying Time Considerations WEB Printing Mounting the Coder Special WEB Printing Applications Gang Mounting Carton Printing Carton AlignmentClearance 1/4 DIE Positioning for Indexing Applications Carton Printing Maintenance PRE-INKING a NEW INK RollCleaning the Transfer Roll Cleaning the CoderCleaning the Printing Dies Pivot ARM & Inking System Assembly Conversion Tension ARM Assembly Conversion Print Drum Index Mechanism Conversion Print Drum Axle Brass TIP Recess Area SET Screw Replacing Print Drum Index Springs Removing and Replacing Index Block B Lift Index Block B straight up to remove Inking System Assembly Maintenance MOUNTINGARM, CLP CE Guard NON-POROUS Conveyor Line Printer Assembly NON-POROUS Conveyor Line Printer Parts List NON-POROUS Conveyor Line Printer Inking System Assembly NON-POROUS Conveyor Line Printer Inking System Parts List CLP NON-POROUS Inking System BaseplateFriction Bearer Ring Square CUT Snap Ring