Vivotek VS2403 manual Power adapter

Page 13

pin 12 and pin 22 to pin 25 can be connected to external sensors and the state of voltage will be monitored according to the programmed conditions on the configuration page or the external script file. Four relay switches can be used to turn on or off external devices. When the system starts up, COMMON of both relay switches will be short with NC. A simple diagram of example is shown below.

If DI1 in configuration is set as rising to drive DO1 to high that denotes COMMON of DO1 short with NO, then the bulb will light when DI1 signal changes from 0V to 12V.

Power adapter

Plug the power jack of the included power adapter to Video Server. Connecting the power adapter should be the last operation while physically installing Video Server. Administrators may feed an external power source through pin 14 and pin 15 of the general I/O terminal block to replace the power adapter.

The power adapter of Video Server and the external power supply are prohibited to

exist together. Only one source can feed power to Video Server. Improper usage will result in serious damage.

- 12 -

www.vivotek.com

Image 13

Contents Page Technical@vivotek.com Before You Use Table of Contents Frequently Asked Questions Package Contents Features and Benefits Remote system upgrade Bundled powerful surveillance softwarePrivacy mask Built-in motion detectionFront Panel Physical DescriptionStatus LED’s Auxiliary button Reset DIP switches 1 toBNC video inputs LED status DescriptionEthernet 10/100 socket Rear PanelCOM port General I/O terminal blockRS485 interface Power sourceDigital I/O control Power adapter How to Install Power on Hardware installationEthernet Environment Cable connectionEasy way with installer program Software installationPage First access to Video Server How to UseSet password of administrator Complete the network settingsAuthentication Installing Plug-in Text mode Graphic modeMain Video input selection System configurationVideo quality selection Video size selectionMotorized camera control Custom camera commandsIntroduction System ConfigurationAdjust date and time Definitions of ConfigurationSystem parameters Change host nameSecurity privilege Basic network settings Network settingsFix the IP address PPPoEPage Ddns & UPnP Enable DdnsFTP settings Mail settingsMail & FTP Allow list Access listDeny list Adjust image settings Enable video channelsConfigure attached motorized camera Video, camera mapping and motion detectionConfigure privacy mask Configure motion detectionSelect default video source Set video modulationPage Custom commands Port settingsCamera Control Choose serial interfaceText mode Image modeHomepage layout Application constitution External command scriptWeekly schedule Event operationSending method Sequential operationView log file Factory defaultView parameters Capture Up-to-date Still Images Advanced FunctionsGet snapshot via URL Get snapshot via FTPSelect video source and quality and size Get Continuous ImagesDisplay all video Get triggered snapshots via URL Download Event-triggered SnapshotsGet triggered snapshots via FTP Channel name Folder nameFile name Value Description Upload snapshots to external FTP server Uploading Snapshots PeriodicallySend snapshots to external Smtp email server Object File name Customize Graphics in HomepageCommand format Command Script for Complex ApplicationsParameter explanation Page Practical examples Command line DescriptionQuery status of digital inputs URL for External Device ControlDrive digital outputs Move motorized camera in PTZ directionSend command to device attached to COM2 Send command to device attached to COM1Transparent Remote Serial Driver Restore Factory Default Settings via URL URL of System MaintenanceDownload System Log via FTP Restart System via URLConfigure System via FTP Viewmode Security Usercount Username 0root Userattr 0video1video2video3video4camctrldidoconf System core debugging Telnet CommandsMonitor changed status of digital inputs Stop information dumpingReset system Restore factory default settingsPower-On-Self-Test TroubleshootingLED pattern after Post Failed function Troubleshooting AppendixReset System recoveryFrequently Asked Questions Page Page Easy way via Installation Wizard Upgrade System FirmwareURL URL Commands of Video ServerHomepage name Referenced URL Resource name Referenced URL System resource URLGet server parameter values General CGI URL syntax and parametersMethod GET/POST Nosync Set server parameter valuesAvailable parameters on the server WirelessVideo Serverwith Pan/Tilt/ZoomYyyy/mm/dd HhmmssSkip to invoke default server 192.168.0.99 Group Security255.255.255.0 LAN Usernameemail Address Group IPFilter255.255.255.255 Ntsc PAL For Ntsc onlyNtsc & Cmos Group Motion1~4Group CAMCTRL1~4 Script.vssx Group Feature Camera model Baud rate Data bits Stop bit Parity bit Settings of Supported PTZ CamerasCamera Control Cable Time Zone Table Page GMT+1000 Hobart Vladivostok GMT+1100 Networking Technical SpecificationsElectromagnetic Compatibility EMC