Vivotek VS2403 manual System recovery, Reset

Page 58

A.2 System recovery

Video Server provides an auxiliary button located on the left of the front panel for system recovery by hardware. The buttons can be used to perform either level of system recovery. “Reset” will force the system restart at any point; “Restore” will restore the default settings from factory and then force the system restart to work at the initial state. Consequently “restore” is generally used to completely recover the system from serious fault in configuration.

RESET

Click on the “RESET” button once. The system will perform the system diagnosis and the software installation may be necessary if the IP address is not fixed. This procedure is as same as removing the power and attaching it again.

RESTORE

When the system seems to respond or operate slowly after changing some settings and administrators hardly enter the configuration to change back the original settings, administrators can perform the “restore” procedure. It is as same as the “factory default” link on the configuration page. To restore the factory default settings, press the “RESET” button firmly. The system diagnosis will start right away and the “status” LEDs will be turn on after system diagnosis. After the “status” LEDs are off, Administrators can release the “RESET” button now and perform the installation for the initialized system.

To reduce the system failure caused by operation error, always read the related

sections in this user’s manual to prevent from unexpected error caused by wild-guess configuration.

- 57 -

www.vivotek.com

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Page Technical@vivotek.com Before You Use Table of Contents Frequently Asked Questions Package Contents Features and Benefits Privacy mask Bundled powerful surveillance softwareRemote system upgrade Built-in motion detectionFront Panel Physical DescriptionStatus LED’s BNC video inputs DIP switches 1 toAuxiliary button Reset LED status DescriptionCOM port Rear PanelEthernet 10/100 socket General I/O terminal blockRS485 interface Power sourceDigital I/O control Power adapter How to Install Ethernet Environment Hardware installationPower on Cable connectionSoftware installation Easy way with installer programPage Set password of administrator How to UseFirst access to Video Server Complete the network settingsAuthentication Installing Plug-in Text mode Graphic modeMain Video quality selection System configurationVideo input selection Video size selectionCustom camera commands Motorized camera controlSystem Configuration IntroductionSystem parameters Definitions of ConfigurationAdjust date and time Change host nameSecurity privilege Fix the IP address Network settingsBasic network settings PPPoEPage Enable Ddns Ddns & UPnPFTP settings Mail settingsMail & FTP Allow list Access listDeny list Configure attached motorized camera Enable video channelsAdjust image settings Video, camera mapping and motion detectionSelect default video source Configure motion detectionConfigure privacy mask Set video modulationPage Camera Control Port settingsCustom commands Choose serial interfaceText mode Image modeHomepage layout Weekly schedule External command scriptApplication constitution Event operationSequential operation Sending methodView log file Factory defaultView parameters Get snapshot via URL Advanced FunctionsCapture Up-to-date Still Images Get snapshot via FTPSelect video source and quality and size Get Continuous ImagesDisplay all video Get triggered snapshots via FTP Download Event-triggered SnapshotsGet triggered snapshots via URL Channel name Folder nameFile name Value Description Upload snapshots to external FTP server Uploading Snapshots PeriodicallySend snapshots to external Smtp email server Customize Graphics in Homepage Object File nameCommand format Command Script for Complex ApplicationsParameter explanation Page Command line Description Practical examplesDrive digital outputs URL for External Device ControlQuery status of digital inputs Move motorized camera in PTZ directionSend command to device attached to COM2 Send command to device attached to COM1Transparent Remote Serial Driver Download System Log via FTP URL of System MaintenanceRestore Factory Default Settings via URL Restart System via URLConfigure System via FTP Viewmode Security Usercount Username 0root Userattr 0video1video2video3video4camctrldidoconf Monitor changed status of digital inputs Telnet Commands System core debugging Stop information dumpingRestore factory default settings Reset systemLED pattern after Post Failed function Troubleshooting TroubleshootingPower-On-Self-Test AppendixSystem recovery ResetFrequently Asked Questions Page Page Upgrade System Firmware Easy way via Installation WizardURL URL Commands of Video ServerHomepage name Referenced URL System resource URL Resource name Referenced URLGet server parameter values General CGI URL syntax and parametersMethod GET/POST Set server parameter values NosyncYyyy/mm/dd WirelessVideo Serverwith Pan/Tilt/ZoomAvailable parameters on the server HhmmssSkip to invoke default server 192.168.0.99 Group Security255.255.255.0 LAN Usernameemail Address Group IPFilter255.255.255.255 For Ntsc only Ntsc PALGroup Motion1~4 Ntsc & CmosGroup CAMCTRL1~4 Script.vssx Group Feature Settings of Supported PTZ Cameras Camera model Baud rate Data bits Stop bit Parity bitCamera Control Cable Time Zone Table Page GMT+1000 Hobart Vladivostok GMT+1100 Technical Specifications NetworkingElectromagnetic Compatibility EMC
Top Page Image Contents