Panasonic KX-HGC200 operating instructions FCC and Other Information

Page 76

FCC and Other Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

76

Image 76
Contents Operating Instructions Attach your purchase receipt here For your future reference Before Initial UseFor Operation Assistance -Call Refer to For Best Performance Location of the unitsTable of Contents Installation Network Manager Appendix Using the Device ManagementOverview FeaturesSystem requirements Included Accessory Contents of the CD-ROMIncluded Accessory To prevent accidental damage to the CD-ROMIndicators Part NamesPart names Status IndicatesInstallation Overview Important parameters to create a wireless networkRequired setup for the Broadband Networking Gateway Network with the Broadband Networking GatewayNetwork consisting only of wireless computers Installation OverviewConfirming the Broadband Networking Gateway firmware version To check the Broadband Networking Gateway firmware versionInstalling the KX-HGC200 in the Broadband Networking Gateway Inserting the KX-HGC200 in the Broadband Networking Gateway 11M Setting up the Broadband Networking Gateway Setting up from a wired computerSetting up the Broadband Networking Gateway Setting up from a wireless computer About the network nameClick Add Installation Setting up the Broadband Networking Gateway Checking the setup parameters Helpful functionsChecking data-transmission status Confirming the PC card service ComputerBefore inserting the KX-HGC200 PropertiesInstalling the KX-HGC200 to a Computer By the Pcmcia socketInserting the KX-HGC200 into a computer Helpful hints Installing the device driver Click Finish While a computer is restarting, mind below notification For Windows Driver is located, and click Next Click Yes to restart the computer For Windows Me ³The device driver will be installed to your computer Click Finish Installing the Network Manager Click Next ³The data setting field isnot case-sensitive Network Manager Taskbar See below Shortcut toIcon Status Confirming the KX-HGC200 setup Select Panasonic 11Mbps Wireless LAN PC Card and click Confirm that This device is working properly. is shownNetwork components are installed list Setting up Your ComputerConfirming the network protocols Installation Setting an IP address Setting up Your ComputerSelect TCP/IP-Panasonic 11Mbps Wireless LAN PC Card Address automatically and click OKClick OK Click Yes to restart the computer Click Control Panel About the IP address and subnet mask Click the IP Address tab and select Specify an IP addressWhile a computer is restarting, mind below notification Sharing Files and Printers Preparing for sharing files and printersMake sure Client for Microsoft Networks is listed About the Network Manager Software Web Screen About the Network Management web screenFunction Menu Node Name Performance Info Identification tab of the Network dialogUsing the Network Management Web Screen Using the function menuNode Information Link Information Bandwidth InformationAdd a New Node About the Device Management dialog box Dialog BoxProperties tab Using the Device Management Dialog Box Configuration tabAbout the network name Forward Error Correction FEC Setting a computer to the Master NodeChanging the channel radio frequency Removing the KX-HGC200 Select Panasonic 11Mbps Wireless LAN PC Card and click StopRemoving the KX-HGC200 from a computer Removing the KX-HGC200 Wireless PC Card and click Firmware Update Updating the KX-HGC200 Firmware ÒUpdating the KX-HGC200 Firmware Uninstalling the KX-HGC200 Software Ò Uninstalling the KX-HGC200 Software Click UnInstall Click RebootTroubleshootingÒ Problem RemedyTroubleshooting ProblemRemedyAppendix Troubleshooting Glossary Glossary Network Manager softwareNode Name Radio FrequencySpecifications FCC and Other Information Appendix Index Appendix For product service When you ship the product