Panasonic KX-HGC200 operating instructions Troubleshooting, ProblemRemedy

Page 70

ÒTroubleshooting

ProblemRemedy

The Network management web screen is not displayed.

You cannot connect with the computer.

You cannot connect with the Broadband Networking Gateway.

³The KX-HGC200 device driver may have not been installed successfully. Make sure the driver is installed.

³The computer and/or the Broadband Networking Gateway may have not been conﬁgured properly. Check the settings of the computer and/or the Broadband Networking Gateway.

³The channel numbers of the computers and/or the Broadband Networking Gateway vary in the same network. Check their channel numbers.

³Even if the Network Names of the computers and the Broadband Networking Gateway are same, their Network ID may vary in the same network. Re-enter the Network Name by using the Device Management dialog box.

³The computer and/or the Broadband Networking Gateway may be out of radio waves, or the concrete wall etc. may be disturbing the waves. Set the computers closely.

³More than one computers are set to the Master Node. Check the setting of each computers.

³Check the setting of the IP address.

³The Network Manager may not be installed. Make sure the “Network Manager” icon is displayed on the taskbar.

³The Network Manager recognizes a different IP address from that of the computer to which the KX-HGC200 is attached. Check the Properties tab of

the Device management dialog box (p. 59), then click [Refresh] to update

the information.

70

Image 70

Contents Operating Instructions Attach your purchase receipt here For your future reference Before Initial UseFor Operation Assistance -Call Refer to For Best Performance Location of the unitsTable of Contents Installation Network Manager Appendix Using the Device ManagementOverview FeaturesSystem requirements Included Accessory Contents of the CD-ROMIncluded Accessory To prevent accidental damage to the CD-ROMPart names IndicatorsPart Names Status IndicatesInstallation Overview Important parameters to create a wireless networkRequired setup for the Broadband Networking Gateway Network with the Broadband Networking GatewayNetwork consisting only of wireless computers Installation OverviewConﬁrming the Broadband Networking Gateway ﬁrmware version To check the Broadband Networking Gateway ﬁrmware versionInstalling the KX-HGC200 in the Broadband Networking Gateway Inserting the KX-HGC200 in the Broadband Networking Gateway 11M Setting up the Broadband Networking Gateway Setting up from a wired computerSetting up the Broadband Networking Gateway Setting up from a wireless computer About the network nameClick Add Installation Setting up the Broadband Networking Gateway Checking the setup parameters Helpful functionsChecking data-transmission status Before inserting the KX-HGC200 Conﬁrming the PC card serviceComputer PropertiesInstalling the KX-HGC200 to a Computer By the Pcmcia socketInserting the KX-HGC200 into a computer Helpful hints Installing the device driver Click Finish While a computer is restarting, mind below notiﬁcation For Windows Driver is located, and click Next Click Yes to restart the computer For Windows Me ³The device driver will be installed to your computer Click Finish Installing the Network Manager Click Next ³The data setting ﬁeld isnot case-sensitive Network Manager Taskbar See below Shortcut toIcon Status Conﬁrming the KX-HGC200 setup Select Panasonic 11Mbps Wireless LAN PC Card and click Conﬁrm that This device is working properly. is shownNetwork components are installed list Setting up Your ComputerConﬁrming the network protocols Installation Setting an IP address Setting up Your ComputerSelect TCP/IP-Panasonic 11Mbps Wireless LAN PC Card Address automatically and click OKClick OK Click Yes to restart the computer Click Control Panel About the IP address and subnet mask Click the IP Address tab and select Specify an IP addressWhile a computer is restarting, mind below notiﬁcation Sharing Files and Printers Preparing for sharing ﬁles and printersMake sure Client for Microsoft Networks is listed About the Network Manager Software Function Menu Node Name Performance Info Web ScreenAbout the Network Management web screen Identiﬁcation tab of the Network dialogUsing the Network Management Web Screen Using the function menuNode Information Link Information Bandwidth InformationAdd a New Node About the Device Management dialog box Dialog BoxProperties tab Using the Device Management Dialog Box Conﬁguration tabAbout the network name Forward Error Correction FEC Setting a computer to the Master NodeChanging the channel radio frequency Removing the KX-HGC200 Select Panasonic 11Mbps Wireless LAN PC Card and click StopRemoving the KX-HGC200 from a computer Removing the KX-HGC200 Wireless PC Card and click Firmware Update Updating the KX-HGC200 Firmware ÒUpdating the KX-HGC200 Firmware Uninstalling the KX-HGC200 Software Ò Uninstalling the KX-HGC200 Software Click UnInstall Click RebootTroubleshootingÒ Problem RemedyTroubleshooting ProblemRemedyAppendix Troubleshooting Glossary Node Name GlossaryNetwork Manager software Radio FrequencySpeciﬁcations FCC and Other Information Appendix Index Appendix For product service When you ship the product