Panasonic DP-2010E, DP-1810P manual Function Setting for Key Operator, Changing the Paper Size

Page 34

Function

Function Setting for Key Operator

■Changing the Paper Size

The Paper Trays are designed to accommodate Invoice, Letter, Letter R, Legal and Ledger size paper. To change the paper size, perform the steps shown below.

1	Press the FUNCTION key.	FUNCTION Key

2	Proceed as Follows:

			FUNCTION MODE (1-2)
			ENTER NO. OR ∨ ∧

	#Press the 1 key to select GENERAL
		FUNCTIONS.

			1:GENERAL FUNCTIONS
			PRESS SET TO SELECT

	$Press the SET key.

			GENERAL PARAM. (0-9)
			ENTER NO. OR ∨ ∧

	%Press 9 key.

			09 KEY OPERATOR MODE
			ENTER PASSWORD=- ■ ■

&Input the Key Operator ID code (3 digit) and the SET key.

KEY OPR. MODE (00-25)

ENTER NO. OR ∨ ∧

(Press 00 and 1 or 2 key to select the PAPER SIZE.

00 PAPER SIZE 1:TRAY-1[LTRB]

)Press SET to select the paper tray and press (G or F) keys to set the paper size.

Paper size changes are as follows.

Letter R Invoice R		A3		B4		A4

Letter						A4R

Legal	B5

Ledger FLS2 FLS1 A5R B5R

*Press the SET key to set up the PAPER SIZE.

+Press the RESET key to exit the Function mode.

34

Image 34

Contents Options Before StartingEnglish Others Important Information Model and Serial NumberOperation Chart Common Features and UsageEnergy Star Table of Contents Options Problem SolvingOthers Laser Safety PrecautionsFor Your Safety Manufacturer’s name and address Factory IDHandling Toner and Paper VentilationInstallation FCC Warning For U.S.AControl Panel Interrupt Key, Memory in Key, M1/M2 Keys Contents Refer to Stop KeyLCD Display Copy Size KeyCopying the Same Size Originals Basic CopyFull Size Copying $Select Exposure ControlSelect the Copy Copying with Preset RatiosReduction or Enlargement Copying Paper Tray keyPress Cursor G or F keys to select Zoom Ratio Zoom CopyingZoom Select OriginalCopying on Special Paper, etc Using the Sheet Bypass$Adjust the side guides Press Start1 Copy Creative FeaturesProcedure PressKey Place PressOriginals CopyPress BOOK, Edge Or Margin keyKey Operation Sided/1-Sided Copy For DP-2010EBook \ Press 2-Sided \ 2 / 2 \1 / 2 \ 2 Copy For DP-2010ESided Copy key Book \ 2 Copy For DP-2010E Place the Original on the PlatenTo Recall a Job Stored in Memory Job MemoryTo Store a Job in Memory $Press the Memory in F2 keySort Copy Sort ModeSort Copy From Platen Glass onlyEnergy Saver Mode Other FeaturesEnergy Saver/Interrupt Mode Sleep ModeSkyshot Mode Digital Skyshot ModeManual Skyshot Mode Platen Upper- left cornerNext Combined Function TableRemarks Job Memory RetrievalUsing Function Modes to Change the Initial Copy Modes FunctionModes Function Initial Setting General FunctionsCopier Settings Edge Default General Functions for Key Operator TCP/IP AddressCopier Settings for Key Operator Press the Function key Function SettingChanging the Auto Exposure Setting Proceed as FollowsFunction Setting for Key Operator Changing the Paper SizeStopper Guide a Paper Guide b IndicatorPaper SizeDepartment Counter Select the Department Counter Mode Page Accessories ComponentsADF DA-AS180 / i-ADF DA-AR201 FeaturesAutomatic Document Feeder ComponentsOriginal OperationPlace Inappropriate OriginalsAdding Paper J Problem SolvingSheet Paper Tray Remove the Toner Waste Container by Adding the Toner and Replacing Toner Waste Container ?Open the Front Cover Slowly pulling it towards the left asProblem Solving Removing a Misfed Paper Paper Misfeed LocationsPaper Exit Area Remove the misfed paperHot Paper Entry/Transport AreaOpen the Right Cover Remove the misfed paper HeatedOpen the Right Cover ADU Area For DP-2010E onlyClose the Right Cover Paper Feed Module ADF For DP-2010E only ADF Check Action TroubleshootingBefore Calling Service Unit Does Not OperateLight Copies Add Toner Warning IndicatorMarked Copies User Error Codes U Code As a rule, clean weeklySpecifications DP-1810P/2010E Copier2nd/4th Paper Feed Module DA-DS182 ADF DA-AS180ADF DA-AR201 3rd Paper Feed Module DA-DS183For Network Printing Options and SuppliesFor Printer SuppliesPage Page Warranty