Panasonic DP-2010E, DP-1810P manual Problem Solving, Adding Paper J, Sheet Paper Tray

Page 42

Problem Solving

Adding Paper (J)

■550-Sheet Paper Tray

	1	Pull the Paper Tray out.
		Pull the Paper Tray out.
	2	Place the paper with the copying
		surface facing upward.
		Special papers, like glossy paper, mailing
		labels and transparencies cannot be used
		in the paper tray.
		Use the Sheet Bypass for special paper.
	3	Make sure paper is not loaded
		Make sure paper is not loaded
		above the overfill indicator located
		in the Paper Tray.
	4	Firmly push the Paper Tray back
		Firmly push the Paper Tray back
		into the copier.
	ATTENTION	CDo not use paper with folds or wrinkles.
	ATTENTION	Refer to page 35 for details on adjusting the paper tray size.

CUnused paper should always be placed into a bag and the opening should be sealed for storage.

If the paper is left exposed, problems such as paper curl, paper jams, wrinkles or loss of copied image quality may occur.

42

Image 42

Contents Before Starting OptionsEnglish Others Important Information Model and Serial NumberOperation Chart Common Features and UsageEnergy Star Table of Contents Problem Solving OptionsOthers Laser Safety PrecautionsFor Your Safety Manufacturer’s name and address Factory IDHandling Toner and Paper VentilationInstallation FCC Warning For U.S.AControl Panel Interrupt Key, Memory in Key, M1/M2 Keys Contents Refer to Stop KeyLCD Display Copy Size KeyCopying the Same Size Originals Basic CopyFull Size Copying $Select Exposure ControlSelect the Copy Copying with Preset RatiosReduction or Enlargement Copying Paper Tray keyPress Cursor G or F keys to select Zoom Ratio Zoom CopyingZoom Select OriginalCopying on Special Paper, etc Using the Sheet Bypass$Adjust the side guides Press Start1 Copy Creative FeaturesProcedure PressKey Place PressOriginals CopyPress BOOK, Edge Or Margin keySided/1-Sided Copy For DP-2010E Key OperationBook \ \ 2 / 2 \1 / 2 \ 2 Copy For DP-2010E Press 2-SidedSided Copy key Book \ 2 Copy For DP-2010E Place the Original on the PlatenTo Recall a Job Stored in Memory Job MemoryTo Store a Job in Memory $Press the Memory in F2 keySort Copy Sort ModeSort Copy From Platen Glass onlyEnergy Saver Mode Other FeaturesEnergy Saver/Interrupt Mode Sleep ModeSkyshot Mode Digital Skyshot ModeManual Skyshot Mode Platen Upper- left cornerNext Combined Function TableRemarks Job Memory RetrievalUsing Function Modes to Change the Initial Copy Modes FunctionModes Function Initial Setting General FunctionsCopier Settings Edge DefaultGeneral Functions for Key Operator TCP/IP AddressCopier Settings for Key Operator Press the Function key Function SettingChanging the Auto Exposure Setting Proceed as FollowsFunction Setting for Key Operator Changing the Paper SizeStopper Guide a Paper Guide b IndicatorPaper SizeDepartment Counter Select the Department Counter Mode Page Accessories ComponentsADF DA-AS180 / i-ADF DA-AR201 FeaturesAutomatic Document Feeder ComponentsOriginal OperationPlace Inappropriate OriginalsProblem Solving Adding Paper JSheet Paper Tray Remove the Toner Waste Container by Adding the Toner and Replacing Toner Waste Container ?Open the Front Cover Slowly pulling it towards the left asProblem Solving Removing a Misfed Paper Paper Misfeed LocationsPaper Exit Area Remove the misfed paperHot Paper Entry/Transport AreaOpen the Right Cover Remove the misfed paper HeatedADU Area For DP-2010E only Open the Right CoverClose the Right Cover Paper Feed Module ADF For DP-2010E only ADF Check Action TroubleshootingBefore Calling Service Unit Does Not OperateAdd Toner Warning Indicator Light CopiesMarked Copies User Error Codes U Code As a rule, clean weeklySpecifications DP-1810P/2010E Copier2nd/4th Paper Feed Module DA-DS182 ADF DA-AS180ADF DA-AR201 3rd Paper Feed Module DA-DS183For Network Printing Options and SuppliesFor Printer SuppliesPage Page Warranty