Panasonic DP-2010E, DP-1810P manual Department Counter

Page 36

Function

Function Setting for Key Operator

■Department Counter

The Key Operator can manage, limit copies, counters and code numbers for each department. (Maximum department counters: 50)

1

Press the FUNCTION key.

FUNCTION Key

 

 

 

2

Proceed as Follows:

 

 

 

 

 

FUNCTION MODE (1-2)

 

 

 

ENTER NO. OR ∨ ∧

 

 

 

 

#Press the 1 key to select GENERAL FUNCTIONS.

&Press the Key Operator ID code (3 digit) and SET key.

1:GENERAL FUNCTIONS PRESS SET TO SELECT

$Press the SET key.

GENERAL PARAM. (0-9) ENTER NO. OR ∨ ∧

%Press 9 key.

09 KEY OPERATOR MODE ENTER PASSWORD=- ■ ■

KEY OPR. MODE (00-25)

ENTER NO. OR ∨ ∧

(Press 14 and the SET key to select

DEPT. COUNTER MODE.

NOTE

CTo reset the function mode, press the RESET key.

 

CContact your authorized servicing dealer to enable the Department Counter feature.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Before Starting OptionsEnglish Others Important Information Model and Serial NumberOperation Chart Common Features and UsageEnergy Star Table of Contents Problem Solving OptionsOthers Precautions For Your SafetyLaser Safety Manufacturer’s name and address Factory IDHandling Toner and Paper VentilationInstallation FCC Warning For U.S.AControl Panel Contents Refer to Stop Key LCD DisplayInterrupt Key, Memory in Key, M1/M2 Keys Copy Size KeyBasic Copy Full Size CopyingCopying the Same Size Originals $Select Exposure ControlCopying with Preset Ratios Reduction or Enlargement CopyingSelect the Copy Paper Tray keyZoom Copying ZoomPress Cursor G or F keys to select Zoom Ratio Select OriginalUsing the Sheet Bypass $Adjust the side guidesCopying on Special Paper, etc Press StartCreative Features Procedure1 Copy PressPlace Press OriginalsKey CopyPress BOOK, Edge Or Margin keySided/1-Sided Copy For DP-2010E Key OperationBook \ \ 2 / 2 \1 / 2 \ 2 Copy For DP-2010E Press 2-SidedSided Copy key Book \ 2 Copy For DP-2010E Place the Original on the PlatenJob Memory To Store a Job in MemoryTo Recall a Job Stored in Memory $Press the Memory in F2 keySort Mode Sort CopySort Copy From Platen Glass onlyOther Features Energy Saver/Interrupt ModeEnergy Saver Mode Sleep ModeSkyshot Mode Digital Skyshot ModeManual Skyshot Mode Platen Upper- left cornerCombined Function Table RemarksNext Job Memory RetrievalUsing Function Modes to Change the Initial Copy Modes FunctionModes Function Initial Setting General FunctionsCopier Settings Edge DefaultGeneral Functions for Key Operator TCP/IP AddressCopier Settings for Key Operator Function Setting Changing the Auto Exposure Setting Press the Function key Proceed as FollowsFunction Setting for Key Operator Changing the Paper SizeIndicator PaperStopper Guide a Paper Guide b SizeDepartment Counter Select the Department Counter Mode Page Accessories ComponentsFeatures Automatic Document FeederADF DA-AS180 / i-ADF DA-AR201 ComponentsOperation PlaceOriginal Inappropriate OriginalsProblem Solving Adding Paper JSheet Paper Tray Adding the Toner and Replacing Toner Waste Container ? Open the Front CoverRemove the Toner Waste Container by Slowly pulling it towards the left asProblem Solving Removing a Misfed Paper Paper Misfeed LocationsPaper Exit Area Remove the misfed paperPaper Entry/Transport Area Open the Right Cover Remove the misfed paperHot HeatedADU Area For DP-2010E only Open the Right CoverClose the Right Cover Paper Feed Module ADF For DP-2010E only ADF Troubleshooting Before Calling ServiceCheck Action Unit Does Not OperateAdd Toner Warning Indicator Light CopiesMarked Copies User Error Codes U Code As a rule, clean weeklySpecifications DP-1810P/2010E CopierADF DA-AS180 ADF DA-AR2012nd/4th Paper Feed Module DA-DS182 3rd Paper Feed Module DA-DS183Options and Supplies For PrinterFor Network Printing SuppliesPage Page Warranty
Top Page Image Contents