Panasonic DP-200 manual General Functions for Key Operator

Page 31

Function

General Functions for Key Operator

	No.	Modes	Function		Initial
	No.	Modes	Function		Setting
					Setting
	00	PAPER SIZE	Sets the paper size of each paper tray.*		Consult
			CTray-1, Tray-2, Tray-3, Tray-4		your
					service
					technician.
	01	AUTO RESET TIME	Selects the Control Panel reset time.		1 minute
			CNone, 30 seconds, 1 minute, 2 minutes,
			3 minutes, 4 minutes
	02	ENERGY SAVER MODE	Sets the Energy Saver mode and time.		Sleep
			CNone, Energy save mode, Sleep mode
			Energy save mode timer : 1-120 minutes
			Sleep mode timer	: 1-120 minutes
	03	ENERGY SAVER TIME	Sets the on time and off time for Energy Saver
			mode.
			CStart time - End time
	04	LANGUAGE DEFAULT	Selects the message language of the display.		English
			CEnglish, French, Spanish
	05	SPECIAL TRAY 1	Sets the paper tray for special paper (ex: colored).		NONE
			CNone, Tray-1, Tray-2, Tray-3, Tray-4, Sheet
			Bypass
	06	SPECIAL TRAY 2	Sets the paper tray for special paper (ex: colored).		NONE
			CNone, Tray-1, Tray-2, Tray-3, Tray-4, Sheet
			Bypass
	09	KEY/TOUCH BEEP	Sets the panel touch sound.		Soft
			COff, Soft, Loud
	10	ORIG. SET BEEP	Beep sound when original is set on the platen.		OFF
			COFF, ON
	11	ORIG. SET BEEP ADF On	Beep sound when original is set in the ADF.		ON
			COFF, ON
	14	DEPT. COUNTER MODE	Monitors copy usage of each department.		Consult
			(1) Copy usage of each department		your
			(2) Copy limit of each department		service
			(3) Copy number of each department		technician.
	20	DATE & TIME	Sets the date & time
	21	DAYLIGHT TIME	Sets daylight saving time		ON
			COFF, ON
	22	TCP/IP ADDRESS	∗ Sets user IP address
			C3 digit ⋅ 4
	23	TCP/IP SUBNET MSK	∗ Sets the subnet mask
			C3 digit ⋅ 4
	24	TCP/IP G/W ADDR.	∗ Sets the gateway address
			C3 digit ⋅ 4

	NOTE	CIt is necessary to input the Key Operator ID code before changing items on
	NOTE	this page.
		this page.

CThe Special Tray 1 and 2 are not auto-selectable in the switching mode. ∗ Not needed in copying mode, but needed when installing options for

advanced functions (see page 61) or using multi functions model.

Making Copies

31

Image 31

Contents English DP-2000Common Features and Usage Operation ChartEnergy Star Table of Contents Options Problem SolvingOthers For Your Safety PrecautionsLaser Safety Handling Toner and Paper Ventilation PrecautionsFCC Warning For U.S.A InstallationControl Panel Stop Key Contents Refer to Function KeyReset Key Clear KeysCursor Keys Contents Refer to Book KeyEdge Key Margin KeyFull Size Copying Basic CopySize Copying with Preset RatiosReduction or Enlargement Copying Select the CopyZoom Zoom CopyingPress Cursor F or G keys to select Zoom Ratio # Place approximately 50 sheets of paper into the tray Using the Sheet Bypass$Adjust the side guides Copying on Special Paper, etcBook \ Sided/Original H Copy Duplex CopySided/1-Sided Copy Key OperationSided Copy key Procedure\ 2/2 \ 1/2 \ 2 Copy Press 2-SidedPlaten Book \ 2 CopyPlace the Original on the Platen Book \ 2 Copy1 Copy 1 CopyPress 1 keyPlace Press Originals CopyKey Margin key MarginBook/Edge/Margin Press Book, Edge orBlank Paper OHP InterleavingPress the Copied key or the Blank key OHP InterleavingTo recall a job stored in memory To store a job in memoryInterrupt Mode Energy Saver/Interrupt ModeEnergy Saver Mode Sleep ModeSetting the Digital Skyshot Mode Skyshot ModeProceed as Follows Setting the Manual Skyshot Mode Press the Function Key Copying with the Manual Skyshot ModeSet Manual Skyshot mode first Platen Upper- left corner SIDED/ORIG Combined Function TableSort CopyInput Identification Code Using Function Modes to Change the Initial Copy ModesFunction OptionsGeneral Functions Modes Function Initial SettingCopier Settings General Functions for Key Operator Copier Settings for Key Operator Changing the Auto Exposure Setting Function SettingChanging the Paper Size Function Setting for Key OperatorPaper Guide a Stopper Guide b Departmental Counter Counter 6 digits Components AccessoriesComponents FeaturesAutomatic Document Feeder ADF DA-AS200/i-ADF DA-AR250Inappropriate originals OperationPlace OriginalPress Sort/Finish key Finisher/Exit Guide UnitDA-FS200 Finisher Platen Face-UpPull out the tape Replacing the staple cartridgeReinstall the staple cartridge #Open the staple cover Adding Paper J Problem SolvingSheet Paper Tray Straight out Replacing the Toner Cartridge and Waste Toner Box ?Open the front cover Slowly pull the waste toner boxWell Install the new toner cartridge intoInstall a new waste toner box Shake the new toner cartridgeRemoving a Misfeed Paper Misfeed IndicatorPaper Misfeed Locations Finisher Paper Transport Area Removing a Misfed PaperOpen the right cover Paper Entry AreaClose the right cover Automatic Duplex Unit ADUSystem Console ADF/i-ADF #Lift up the ADF Input Tray Action TroubleshootingBefore Calling Service CheckPlaten Cover As a rule, clean weeklyLight Copies Marked CopiesBattery Replacement Required Message Replacing the BatteryBattery Replacement Procedure DP-2000 Copier SpecificationsBin Finisher DA-FS200 ADF DA-AS200, i-ADF DA-AR2502nd/3rd/4th Paper Feed Module DA-DS210/DA-DS200 Part Name Remarks Options and SuppliesFor Printer For FaxWarranty