Panasonic DP-200 manual Removing a Misfed Paper, Paper Transport Area

Page 50

Problem Solving

Removing a Misfed Paper

■ Paper Transport Area

CMake sure that the misfeed indicator goes off after removing all misfed paper.

1

Push the latch to open the cover.

 

2

Remove the misfed paper.

 

3

Close the cover by pushing the

latch.

(Check that the latch is securely

fastened.)

ATTENTION

CMake sure that the misfeed indicator goes off after removing all misfed paper.

 

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents
DP-2000 EnglishOperation Chart Common Features and UsageEnergy Star Table of Contents Others Problem SolvingOptions Laser Safety PrecautionsFor Your Safety Precautions Handling Toner and Paper VentilationInstallation FCC Warning For U.S.AControl Panel Clear Keys Contents Refer to Function KeyReset Key Stop KeyMargin Key Contents Refer to Book KeyEdge Key Cursor KeysBasic Copy Full Size CopyingSelect the Copy Copying with Preset RatiosReduction or Enlargement Copying SizePress Cursor F or G keys to select Zoom Ratio Zoom CopyingZoom Copying on Special Paper, etc Using the Sheet Bypass$Adjust the side guides # Place approximately 50 sheets of paper into the trayKey Operation Sided/Original H Copy Duplex CopySided/1-Sided Copy Book \Press 2-Sided Procedure\ 2/2 \ 1/2 \ 2 Copy Sided Copy keyBook \ 2 Copy Book \ 2 CopyPlace the Original on the Platen Platen1 key 1 CopyPress 1 CopyKey CopyPlace Press Originals Press Book, Edge or MarginBook/Edge/Margin Margin keyOHP Interleaving OHP InterleavingPress the Copied key or the Blank key Blank PaperTo store a job in memory To recall a job stored in memorySleep Mode Energy Saver/Interrupt ModeEnergy Saver Mode Interrupt ModeProceed as Follows Skyshot ModeSetting the Digital Skyshot Mode Set Manual Skyshot mode first Platen Upper- left corner Copying with the Manual Skyshot ModeSetting the Manual Skyshot Mode Press the Function Key Copy Combined Function TableSort SIDED/ORIGOptions Using Function Modes to Change the Initial Copy ModesFunction Input Identification CodeModes Function Initial Setting General FunctionsCopier Settings General Functions for Key Operator Copier Settings for Key Operator Function Setting Changing the Auto Exposure SettingFunction Setting for Key Operator Changing the Paper SizePaper Guide a Stopper Guide b Departmental Counter Counter 6 digits Accessories ComponentsADF DA-AS200/i-ADF DA-AR250 FeaturesAutomatic Document Feeder ComponentsOriginal OperationPlace Inappropriate originalsPlaten Face-Up Finisher/Exit Guide UnitDA-FS200 Finisher Press Sort/Finish keyReplacing the staple cartridge Pull out the tapeReinstall the staple cartridge #Open the staple cover Sheet Paper Tray Problem SolvingAdding Paper J Slowly pull the waste toner box Replacing the Toner Cartridge and Waste Toner Box ?Open the front cover Straight out Shake the new toner cartridge Install the new toner cartridge into Install a new waste toner box WellPaper Misfeed Locations Misfeed IndicatorRemoving a Misfeed Paper Finisher Removing a Misfed Paper Paper Transport AreaPaper Entry Area Open the right coverAutomatic Duplex Unit ADU Close the right coverSystem Console ADF/i-ADF #Lift up the ADF Input Tray Check TroubleshootingBefore Calling Service ActionMarked Copies As a rule, clean weeklyLight Copies Platen CoverBattery Replacement Procedure Replacing the BatteryBattery Replacement Required Message Specifications DP-2000 Copier2nd/3rd/4th Paper Feed Module DA-DS210/DA-DS200 ADF DA-AS200, i-ADF DA-AR250Bin Finisher DA-FS200 Options and Supplies Part Name RemarksFor Fax For PrinterWarranty
Top Page Image Contents